Search results

  1. petercro

    Some things to ponder...or not.

    Keep an eye on this thread. I do believe it will produce results. http://www.e-cigarette-forum.com/forum/modders-forum/70716-precision-juice-injection-drop-drop.html
  2. petercro

    The E-Pipe Juice Machine

    I would just like to take a minute thank Clyde. For his kind words. Especially after the tubing glue problems at first. I have learned the lesson that a small amount of glue, so the mod looks neat, is not always the right way, (Not enough glue to hold the tubing in place). Mike I did ask mine...
  3. petercro

    The E-Pipe Juice Machine

    Mike Out loud is good. Remember though, you would be sucking from a vacuum. With a short tube and full bottle it is easy, longer tube and nearly empty bottle, a lot harder.
  4. petercro

    The E-Pipe Juice Machine

    Hello all. Been away for a day or so. Venting the bottle. I did consider adding an air inlet valve to the bottle, but if I did the reverse suction would be lost. Clyde is correct, if you fill the bottle, the atty will self prime. If you wish to use suction priming, below 75% full then just...
  5. petercro

    510, pre-heat the air?

    This is just my opinion, but I think the result of sliding the bottle down will be the same. It is the airflow that is changing the vape quality in this case. I agree though, Heat causes a dramatic change in vape performance. Try this for a little experiment. Vape with no cone attached. (note...
  6. petercro

    My homemade mini juicebox (the MrPuffer)

    Mr P If you have problems speaking during the transition process. Use my thread. Lots of look. PM me when you are able. Peter.
  7. petercro

    The E-Pipe Juice Machine

    Mike is correct. But I do have some other hobbies which take up some of my time. I Make floors. Terrazzo to be precise. And most of my work is within (I'm ashamed to say) pharmaceutical construction. Or Clean-Room environments. I design, Diamond Polish and install antistatic clean-room floors...
  8. petercro

    The E-Pipe Juice Machine

    Liquid viscosity update. Now on approximately 88 - 90% VG Liquid takes 8 -9 seconds to reach the atty, but working in 3 degs temp. In my hotel room , very warm it only takes 5 -6 seconds. I must say vape is just so much better with VG.
  9. petercro

    My homemade mini juicebox (the MrPuffer)

    Mike the code is straight forward. A basic 3 dimensional cutting subroutine. The bit I don't understand is that I thought a Mastiff was colour blind. LOL
  10. petercro

    My homemade mini juicebox (the MrPuffer)

    Thanks Clumsy:D
  11. petercro

    The E-Pipe Juice Machine

    Mike Nice craftsmanship. Would the spring be too violent or is it smooth.
  12. petercro

    I do like Oscar Wilde Quotes.

    I do like Oscar Wilde Quotes.
  13. petercro

    What is wrong with me...

    Hello All I'm new to this thread, and new to vaping, just 60-ish days. But I must say! Yes to nicotine addiction, Yes to online shopping addiction, but most of all. I believe it is addictive not to smoke. I get the biggest buzz from not smoking, after 35 years of doing so. And for the last...
  14. petercro

    New Pipe Design (picture inside)

    Jason. To me the benefit of a churchwarden is the long stem containing thin batteries. And the bowl, containing liquid. OR. The long stem containing liquid and the bowl contains a battery. Keep in touch, as your knowledge of analogue pipes may help in the build of e-pipes.
  15. petercro

    Adapter to raise atty resistance. Help needed

    Would an old 510 e-cig battery be easier to work with. Remove Cell, cut to length, insert components and an atty connector.
  16. petercro

    The E-Pipe Juice Machine

    Thanks for the input. I have considered that but the liquid feed tube may be a little hard to work with.
  17. petercro

    The E-Pipe Juice Machine

    I will never make any money as I just like my ideas to be scrutinized. And I'm away from home again, for the next 12 days or so. So no playing for me, all I can do is think, talk and vape. Try this one in the brain storming mix TWalkers thread is looking at precision liquid injection. The...
  18. petercro

    My homemade mini juicebox (the MrPuffer)

    Hi All Does anyone know of a UK supplier for these 3ml dropper bottles. Thanks in advance. Petercro
  19. petercro

    where can I get pre-wired 510 connectors?

    Try Mad Vapes MadVapes LLC If they are not listed, just mail Mark, I'm sure he will help.
  20. petercro

    The E-Pipe Juice Machine

    With my eyesight. Can you buy a usb electron microscope.
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu