Search results

  1. Joshuasculptor

    Wood Clickfet saying resistance is to low

    I purchased a clickfet. I am using a single 18650 I wired it exactly like the diagram said and I am getting 3 flash(low resistance) no matter what size coil I put on the 510 connector. Have you guys ever ran into this problem before and if so what was the cause? I'm thinking I might have gotten...
  2. Joshuasculptor

    For the steampunk modders

    Check this guy out he makes traditional pipes but... http://www.natekingpipes.com
  3. Joshuasculptor

    Building an E pipe

    Okay I am working on an epipe. I'm trying to finish the button part. I am using a brass piece that has the standard spring and magnet in the center. I have gotten it made but I am just not to happy with the button action. The whole setup just seems half ... for a lack of better words. Just hard...
  4. Joshuasculptor

    Wenge wood mod

    Wenge Wood Mechanical Mod Well this is not my first battery mod, but it is the first mod I felt is worthy of being posted. Mechanical battery mod similar in design to others. It holds one 18490/18500 battery Wood is from Africa known as Wenge (Pronounced WHEN-gay) The battery cover and the...
  5. Joshuasculptor

    IMR Batteries "What exactly does "IMR" mean?"

    Borrowed from: HERE Battery Guy What exactly does "IMR" mean? Greetings Everyone, I have seen a lot of threads recently on "IMR" lithium-ion cells. DFiorentino and myself have posted some test results recently (seen here and here, respectively). I also have seen a lot of comments...
    • Joshuasculptor
    • Thread
    • batteries battery chemistry ecigexpress evic fasttech imr safe
    • Replies: 18
    • Forum: Devices
  6. Joshuasculptor

    I'm an Idiot! Once again

    So I just got a really good deal(oops wait a min first clue) on 8 - 18350 ultrafire protected xsl orange skinned batteries at fasttech...... S..O....B>> Okay so I just found out I've been duped. Not protected well kinda I read this page about battery anatomy The Anatomy of a Protected Battery So...
  7. Joshuasculptor

    UD Agi Spring Fix (pics)

    I cut off 10.5mm of a 16g blunt end syringe I got from wizard labs. Removed spring from the 510 connector shaft Then I used a punch and hammer to gently tap the tube on to the 510 connector shaft in place of the spring. I measured resistance on my multimeter leads(2ohms) then I read resistance...
  8. Joshuasculptor

    Hello new members put one of these on your list of must haves.

    XB-866 Auto Range Digital Multimeter - Free Shipping - DealExtreme This one cost $10+ shipping and there are many more to choose from.
  9. Joshuasculptor

    Quick Tip - How to get it unscrewed!

    If your mod, Aga t2 rba, or even the two are stuck together from over tightening. FYI - Just put some black tape around each part to give yourself that little bit of extra grip. I found this out after filing my natural down so my aga would fit snug with no gap. After putting the top on and off...
  10. Joshuasculptor

    Simple DIY EJuice Mixer

    Okay I posted this in the diy section. This video is just to get the idea out there. Nothing fancy! Plenty of room for improvements... Have at it. Someone in the diy was looking at mini blenders on line I I mentioned you could make one out of an old printer an things laying around the house...
  11. Joshuasculptor

    Golly Gee Willikers Batman!

    Last night I was about to test some diy juice but didn't have any dry atties. So I pulled the stuffing out of some LR cartos and put one on my VMax and left it set at 3V. I dry burned it about 2 or three times to make sure I didn't mess up the coil and to be sure I got rid of the horrible taste...
  12. Joshuasculptor

    tobacco extracting

    I stumbled on to this today when looking into tobacco extracting. What do you think? Here is the source: Sciencemadness Discussion Board - Nicotine Extraction and purification - Powered by XMB 1.9.11 "OK, to close this off and leave something for others attempting this same item, I finally did...
  13. Joshuasculptor

    Vmax with dual coil Genesis style tank

    Anyone have trouble with the 1.3 ohms limit? My solution was to run the coil itself in series. The problem I'm having is 1 coil seems to be getting hotter than the other and battery drain. My coil and ss mesh coil experience is limited I have had some hot spots but I did not know if that would...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu