Search results

  1. xlambox029

    plating?!

    Has anyone ever silver plated their own copper contacts, if so was it noticeable?
  2. xlambox029

    can't seem to find what I am looking for on batteries

    Can a efest imr 18650 high drain 3.7v battery handle a .4 ohm load. The amp draw would be about 10.5. But I can't seem to find the specs for these batteries, I've heard anywhere from 8-10amp draw can someone help me out?
  3. xlambox029

    ss mesh wicking issues

    I've seen one othe post and there was no answered question so can someone please help. I am using 400 ss mesh for a Nobel 1. Rolled it oxidized, burned juice on it, everything I've ever read on ss mesh watched every vid, but everything I do I can not get the mesh to wick up to the coil, if it...
  4. xlambox029

    heating of coils

    I have a cyclone atty runnig on a mech mod running 32 awg kanthal 5/4 wraps dual coil 2.1 each coil so 1.0 altogether. When I test fire on the ekowool 3 mm should the coils instintly start glowing middle out or if they are not why aren't they glowing?? No wire touching anywhere it shouldbt no...
  5. xlambox029

    coil talk

    Example: when some one say a 7/6 wrap does this mean there will be 7 wraps looking from the top and 6 seen underneath?
  6. xlambox029

    keep popping coil

    Using 30 qwg kqmthal 6 wraps on a cyclone atty with a tridentech mod looked for shorta even spacing ways going on?
  7. xlambox029

    ohms law question

    So I am running cyclone rda atty on a trident mech mod, 32 awg 5 wraps running at 1.3 ohms. Full charge battery so 4.1 volts, my question is I plugged the resistance and volts in oh.s law calculator and it give me a amperage of about 4 amps. Is this correct or is there something I am doin wrong...
  8. xlambox029

    cyclone rda question

    I'm running a cyclone rda on a trident mech mod. 32 awg 5 wraps running at 1.3 ohms. 18650 imr battery, my question is is it normal for the atty to get pretty warm it not like burning but it is def some hear on it, the tube isn't hot at all nor the drip tip just the atty shell. Is this normal?
  9. xlambox029

    trident vs. vanilla

    So I'm going to get my first mech mod tomorrow, I've narrowed it down to either the underdog customs Trident or the Vanilla. Can anyone give me a few opinions about the two positives and negatives? I've read quite alot bout both but If imma spend the money on it I'd like some opinions from...
  10. xlambox029

    slow to heat up dual rda

    I am running a dual set up on a basic rda with 32 awg kanthal 5 wraps each coming out to 1.8 ohms together they are .8. The device is a vv mod I havent trimmed excess wire yet but when I go to fire they take quite a while to heat up. Is this normal or could there by a problem with the posts?
  11. xlambox029

    how to tell resistance vs non resistance wire

    I won't 30 awg kanthal so I thought but every wrap I attempt ohms come out to 0.0, will not heat up and nothing happens. I'm building coils for a cyclone RDA arty and can not seem to ffigure this out. Posts are good no wraps touching even spaces no wire touching other then post holes. Could I...
  12. xlambox029

    please help

    So o bought 30 gauge kanthal and have been trying all different wraps bout I always get a reading of 0.0 and the coil won't fire, I've wrapped coils before and am somewhat experienced with it but can't seem to figure this one out any thoughts?
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu