Search results

  1. VWFringe

    Funny Schematic

    Hope you enjoy...off-topic, just a funny pic...or could it be next years' e-cig? xkcd: Circuit Diagram
  2. VWFringe

    JB Weld Colored With Paint Pigment (Probably Work with Epoxy)

    JB Weld Mixed with Black Paint Pigment ~10 drops 45 minutes with a file and 60,400,1500 sand papers (what I had on-hand) When I'm holding it it looks straight (hehe). Daughter says it's ugly, but all I can see it black jb weld (hmmmm!) I asked nicely for a tablespoon of pigment at...
  3. VWFringe

    Root Canals in Dentistry and Propylene Glycol (PG)

    Several years ago it was found that propylene glycol was an effective carrier for anti-biotics inside the tooth (it spread the anti-biotics throughout the dentene). So, PG instead of water, allows anti-biotic to penetrate the infected tooth. Instead of scraping away all of the infected dentene...
  4. VWFringe

    VWFringe Flashlight Mods - gimme some jbweld love guys

    posted this before in the battery section, but i'm looking for some jb weld love.... -------------------------------------------------------------------------------- I made these flashlight mods for my sister's family after I got six free 18650 batteries out of an old laptop battery pack...
  5. VWFringe

    Is There Any DIY Way To Color JBW or Epoxy Black? (Homemade Pigment/Colorant)

    Any suggestions for changing the cheap yellow epoxy black? I see epoxy pigment available online for $10 plus shipping, but was hoping crushed up charcoal or something simple might be known EDIT: I may try mixing in black nail polish (have to buy some).
  6. VWFringe

    Disatisfaction After Change to LR 510 (from 4.5v with 2.3 ohm atty)

    I thought the wattage would be pretty close switching from four and a half volts with reg attys, to low resistance on a 3.7v cell, but there's a noticeable difference I think in throat hit. It's just not as close to an analog as the 4.5 volts with standard attys. There is plenty of vapor, just...
  7. VWFringe

    VW Push-Pop

    I posted the switch idea but figured I had to finish it to get any love the roller on the switch arm helps, i can pick it up and squeeze without looking for the switch when i first put it together my battery was a few hundredths too long, so had to re-solder the top, which created a gap...
  8. VWFringe

    Switch Ideas

    I often come up with ideas, but may never use them, but they may be usefull to others, so I beg your pardon for sticking them here... Push-Pop - Switch Idea this is not put together, but thought it worth sharing the idea for the switch placement in use the roller makes all the difference...
  9. VWFringe

    1st Flashlight Modz

    EDIT: here's what they will look like, but the washer will get pressed in a bit, obviously my version of the ugly stick, props to the ugly stick. just had to share ahead of being completely done, I've thought about how to do it for so long it feels like they're already done. I'm so proud of...
  10. VWFringe

    Returns to Liberty Flights - Any Experiences?

    30 ml bottles rec'd from Liberty Flights - two of four leak due to poor injection molding. After two emails I was told I need to return them. They cost fifty cents and I am unwilling to pay for shipping. Should pictures and a video clip posted on youtube suffice, or should I just take my...
  11. VWFringe

    DIY Battery Protection Questions

    Everyone gets the free bats but how do you add protection? A: solder on a circuit protection board shown below (link to how-to guide: http://www.technfun.com/soldercells.shtml) Why do you add protection? A: (see Forum FAQ's) Where do you get the PCB's (protection circuit board) or CPM's...
  12. VWFringe

    Salt Etched Copper Picture from Xerox Copy

    OMG laser print onto magazine print (thinner paper) iron the toner onto clean smooth copper cool in cool water soak in warm water peel off paper layer by layer, then rubbing with thumbs, leaving toner intact etch in salt water (2 cups:1 gal. or 1 tsp:1 qt) attaching positive to copper...
  13. VWFringe

    Would This Work? LED as Heat Source for Atty

    could a high power LED be used instead of a coil in an atty? cotton pad over it no more dry-burns, just get a new q-tip, lol ...i was perusing the LED drivers for something that could fire an atty - some do say 2500 mA regulated output (anyone know if that might work?), but then I wondered
  14. VWFringe

    Would This Work? Genesis Atty - Alternative Materials

    how would you expect these to work if used in a genesis atty? ceramic wicks Ceramic Wick for Liquid Mosquito Repellent & Essential Oil they are marketted for mosquito repellent burners like these pictured (my air freshener's isn't ceramic), and also fragrance sticks, so I imagine...
  15. VWFringe

    Question About USB Chargers for Mods

    several of the cheap 18650 USB chargers have step-up converters that dont provide enough electricity for atty's Is it possible to tap into the battery directly, but still use the charging circuit when you're not using the battery, and what would happen if you were to use it while charging...
  16. VWFringe

    Nic Juice Fumes - is it normal i feel it just opening the bottle?

    is it just in my mind, or can i actually feel nic juice fumes while mixing DIY? i know there's no skin contact, just feels kind of heavy when i'm mixing like there's nic fumes coming off of it, and i bump my head on them...weird
  17. VWFringe

    Flavors for VG Juices

    what flavors are strong enough to use in VG? (Fruits preferred but others too) My sister's boyfriend is PG "intollerant." Since it's a political issue, and not a true PG health issue, it's okay if there is PG in the flavor. would like mango, or a rich fruit flavor like that i've found...
  18. VWFringe

    Need Nature's Flavors Recommendations

    Please post Nature's Flavors experiences from their coffee and tea flavoring system only (no PG). I just got off the phone with them, and they are no help at all. The person I was transferred to would only say they do not make it for that application and so have no information, that i would...
  19. VWFringe

    Idea to Shorten 510 and Angle Mouthpiece (Tilt Cup to Stop Spitting)

    has anyone played with making a 90 degree bend between the atty and the drip tip? Perhaps shorten the atty to keep it close to the tip? i'm thinking of a battery mod that would lie flat, just be a bare 18650 pretty much, but instead of just slapping the atty alongside the battery, tilt the...
  20. VWFringe

    Rant: Railing Against "Dual-Use" Cranks

    sorry if this has been posted before I'm appalled by the short-sitedness of those public figures who are against reduced harm tobacco products because they say it will bring in new users and promote "dual use" users, who are described as those who will smoke any chance they get, but use the...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu