Search results

Try to wick it to half of the juice channel. Not too thin tails. Sent from my ASUS_Z00AD using Tapatalk

I tried to use it as my daily gear but it will last me till early evening only. Which is fine as its over office hours. Now I re-coil it with parallel 26g kanthal 5 wraps 2.5id comes to 0.3ohm. Hitting it with 40watts. I think it will last me till around 5pm today. Let's see. Sent from my...

Sorry for that ciggy pack. Just wanna show how small it is and it's just next to me. Should've used the lighter. Sent from my ASUS_Z00AD using Tapatalk

Just got mine today. Coil it with Quad Twisted 30 gauge. 2.5ID 0.55ohm. 30w. Loving it so far. For comparison: Edit: there I dug out my zippo for this picture. [emoji4] Sent from my ASUS_Z00AD using Tapatalk

Try to push the top of the deck down till you hear a click. Happens to mine too. the 521 tab pushed too hard from the pin and it slacks about .5 mm Sent from my ASUS_Z00AD using Tapatalk

Just got mine for about 3 days. Been tinkering around with the notch coil with lil success. Have yet to find the right setup. But then to those who have problems with the glass section being too tight and also hard to fill her up. Here's what I do. Remove one O ring from the bottom. I had the...

No worries. Viewed thru web browser. From the looks the tails are too short. I have mine about 1/4 into the channels. I don't have my zephy with me so I can't take pics for you. Lend it to a pal. Get the wicks a lil longer and tuck em to the juice channel. Then it should work fine. Sent from...

I believe it's your wicking issue. Maybe the tails too short or you have the wick too thin. Post up a picture so we can have a look. [emoji4] Sent from my ASUS_Z00AD using Tapatalk

Currently my fav bring around. Sent from my ASUS_Z00AD using Tapatalk

Its not only in tc mode. Even when using kanthals. So do take extra care. Now I stick to vaping it safely at a cooler setting. Sent from my ASUS_Z00AD using Tapatalk

Finally got it fixed! Problem is due to a loosen wire on the 510 pin on the positive side. Can be due to high heat due to constant high wattage vaping. Vaping happily again now. Sent from my ASUS_Z00AD using Tapatalk

Noted with thanks @pevinsghost Sent from my ASUS_Z00AD using Tapatalk

I've had mine for just less than 2 weeks. This morning the ohms started to jump around like a mad rabbit. I thought its my coils acting up so off I go and recoil my bellus and screw it back on. Behold, it kept on saying 'ohm to high'. I though its the tank swap out with my mini goblin and Same...

Just had mine for 3 hours and going thru the 20th ml of juice. Running with dual coils 24g 5 wraps 2.5mm id coil height at exactly next to the airflow hole. 0.19 ohms hitting at 60w on my xcube2. I never thought I would put down my Zephy tank for it. Just love the flavour out of it. Never had a...

To me it was never the nic. It's the smoking action that I wanted. Needed to keep myself busy when working. I used to smoke a lot when doing programming and analysis. Now with vaping I can do with or without nic. Thou sometimes even 3mg makes me dizzy cause I chain a lot. Still all the better...

Just decided to chip in a bit. OP mention the use of the batteries in a mech before. By chance are both the batteries are used before in a mech? How long have the batteries been in use? IMHO, maybe, just maybe the batteries are way past their charge cycles. Vape on!

Loving this great mod too! I find that I love to work around TC with Ti coils. Have not much luck with Ni. A dual Ti 28g12 wraps 3mm id gave me around 0.54 ohm at room temp in my magma v2. Lock it down and running at 35 joules at 360f. Clouds everywhere. Vape on!

I think that may due to a loose screw holding the coil down. That's why its jumping. 0.7ohm can try out at 15 watts big full open airhole. Vapor production also has to do with your VG content, airhole and coiling. What wires you using now at what size, how many wraps and what internal diameter?

It will. You're using a subtank mini right? It will perform well. Even with other tanks.

So far I've non other than the presets resetting problem. And I've had a trick to get it not to reset. You can read at my post. A 120w power machine and TC mod. Nothing more I can ask. Also a notable feature. If say my current battery level are not safe to run a 0.2ohm build dripper it will not...