Search results

  1. B

    ### Share Your RBAs Setup###

    Tks ash... Like I mentioned, dunno abt my wire but I'm recording 0.4ohms. For the pv, I got a tec mod. I know it prob isn't as efficient as the high end ones I see u guys using in here, but it was the only one I could lay my hands on. :(
  2. B

    ### Share Your RBAs Setup###

    Didn't know over wicking will interfere... Didn't wanna fry the cotton, that's why I used more cotton to soak liquids. Will try cutting down. Tks!!
  3. B

    ### Share Your RBAs Setup###

    Is this better? Tats the best I can do....
  4. B

    ### Share Your RBAs Setup###

  5. B

    ### Share Your RBAs Setup###

    Sorry.... Pic is blurred. I'll try to post a clearer one
  6. B

    ### Share Your RBAs Setup###

    This is wat I've done. Can anyone tell me what went wrong? Btw, I'm not sure what gauge kanthal I using. And even when I use fresh batts, still can't get big vapor.
  7. B

    ### Share Your RBAs Setup###

    Hi, I just started out w rba. Can u explain wat y mean by twisted kanthal? I'm running twin coils on an IgoL w cotton wicks, coming in at 0.4ohm. But just can't get that stupendous amt of vapor tat I'm aiming for. I even bored out the air hole to 2.5mm, now draw is too airy. Tried re building...
  8. B

    Regulated voltage?

    I like my vapor to be a little on the warm side, so I like to vape around 8.5-9W... Some folks like it cool, so they may vape at 5-7W... Some folks like it char broiled, so they may vape at 12-14W... That reminds me, my vivi gets pretty hot if I take a few long drags. More so if I crank up the...
  9. B

    Regulated voltage?

    Makes sense now.... VV stays at the selected power, although not all stays accurate when batt drains. Is that what the micro processor in the Provari is for? Another thing for VW mods, if it selects the correct voltage for the particular resistance atty on the mod automatically..... Why then...
  10. B

    Regulated voltage?

    Can u guys advice some PVs that has inbuilt regulated voltage? Been using ego twist which works fine. It doesn't lose power even when almost flat.... It just goes flat., just got a mech mod. But dislike the taper in power as the batt is being used up. Question : Does these mods below...
  11. B

    Help w ordering frm outside MY.

    Tks for all inputs. Search continues.....
  12. B

    How many People are actively here?

    Yes actively lurking... But like one member mentioned, if no toys to play with... Nothing to talk abt. Sad but true. Sick of getting ripped off by local supp... Yet still dunno how to bring in myself. If this goes on, it won't be long before I reinstate my windproof lighters. :)
  13. B

    Help w ordering frm outside MY.

    Tks Tazieff.... I've tried looking up info frm their webby, but still don't understand. Can I trouble you to explain further? Drop me a PM if it's inconvenient here pls.
  14. B

    Help w ordering frm outside MY.

    Hi guys, I'm based in JB. Wanting to order PVs, tanks cartos...etc frm foreign websites. Will I be taxed for these stuff? Looking at Healthcabin and some US sites as well. Any advise for a first timer?
  15. B

    Which carto tank???

    In relation to my other post, I've been reading up on tanks. And I'm still unsure of which to get. Been imposing on a friendly veteran in here, but think I've disturbed him long enough. Hope other vets here can lend a hand. I see tanks which have locking rings and some without. Some with...
  16. B

    Single coil cartos Kanger or Boge?

    Hi all, I'm abt to try my first carto tank. I've decided on 4.5ml Smoktec dct. Using 35mm length cartos. Going along with the masses, I've decided to get Boge single coils in LR and SR for use on a mech mod and a VV mod respectively. However, Boge cartos seem to be somewhat flying off the...
  17. B

    Ego dct cartomizer question

    Sorry to side track.... I'm lookin at trying carto tanks, I've seen some cartos w flange stated by seller to use w dct tanks. So if I get a dct tank, do I use normal cartos like Boge510 or do I get those w flange??
  18. B

    Hi, u will need at least 5 posts to use PM function. Once u can do tat, drop me a pm. I'll...

    Hi, u will need at least 5 posts to use PM function. Once u can do tat, drop me a pm. I'll advise u frm there. Pls be careful what u post in here.... Many eyes watching. or if u can find a way for us to touch base.... And btw.... Welcome to ECF!
    • Burp
    • Profile post
  19. B

    Why can't I find a flavor that I like?

    Guess we all go thru that in due time.... After frantically trying all available juices we can get or hands on.. Hoping it will be the "one". But it's a matter of time our taste buds get tired of that flavor and the whole process starts agn. What I do is DIY some menthol juice On standby at...
  20. B

    Protected/unprotected?

    Sorry for the noob question ppl.... I'm thinking of upgrading to a vv pv. But I'm reading all this diff kinds of batts that may or may not work w this pv or that pv.... Really got me mixed up. Protected, unprotected, imr, highdrain.??? Can some one pls advise what the diff w all these batts?
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu