I tried the scottish roll. But dunno if I did it correctly. For sure, no leaking. Shall monitor the weak vape and wick breaking issues.
But I do notice that the flavour is more intense than I previously did with normal wicking.
Thanks for the advice.
I realized that the wick always break into half when i pull the wick out from the coil. Suspect that the wick broke and that coz the wicking problem. But I do not vape in high temp. Dunno why it always break one. Now put in a new cotton and try again.
Yes, I did lock the resistance. I also realised that when the firing is weak or not firing, I will open the filling cap and leave it open for awhile. After that cap back and the firing is OK.
Sorry to hijack this thread. But I really need some advice but do not wish to open another thread.
I have been building titanium coils (spaced and contact coils) for the past 3 weeks on tfv4 without success. Running the tank with ipv d2 or evic vt mini.
Every time I build a new coil, the first...
Yes. Did a cotton test with evic vt. I see the discoloration at around 390F. Adjusted down to 370F and seems to be OK. But the flavour is very mild and not to my liking.
Now the new coil I did last night is not working. Did refill to 1/2 tank. Firing is super weak at 450F at 26w.
Could there...
Hi,
Yes, I am using the single coil rba. The screw is tight. I noticed that my cotton is always broken in the middle. It is very easy to remove the cotton from the coil. It will break into half.
Did a new spaced coil. 24awg ti gr1 with 8 wraps. Resistance locked at 0.28 running on evic vt...
Hi all,
I have been building titanium coils (spaced and contact coils) for the past 2 weeks on tfv4 without success. Running the tank with ipv d2 or evic vt mini.
Every time I build a new coil, the first 1/2 to full tank would feel good vaping. But the firing would weaken on the next refill. I...
Problem again. Recoil with titanium. Vape almost 1/3 of the tank. Then suddenly error message from mod. "no liquid". Let the tank cool down and try to lock the resistance again. Error message came again. "check atomizer". Put to another mod. Also same error message. Dunno where I did wrong...
I read somewhere saying putting a little wick into the juice well. I did that but also leak.
Just now when i first refill it leaked, until below the chimney then stop leaking. Then I try top up the juice above chimney but no leak. So I dunno when the leak is from.
Ok. So what I will do tonight.
1) coil the titanium wire.
2) screw to rba and adjust coil.
3) assemble the tank.
4) fill up with juice
5) fix to temp control mod
6) leave it for 5 to 10 mins and wait for it to cool to room temp
7) lock resistance. Set temp and coil type.
8) ready to fire
I read from a guide is to lock resistance first. Then set the temp and coil then fill up with juice. I will try your steps given to me. But why can't I lock the resistance now with juice inside?
Mine also leaks went refill but I dunno where the juice leaked thru. I using rba. Probably also same as u. Between rba and rba cover. Tonight I go monitor.
Hi guys. Got a problem here. Got my titanium 24 Guage wire. Did a 10 wraps with 3mm screw driver in tvf4. Managed to lock the resistance at .48 ohms with ipv d2 and filled up the tank. Vape for awhile and ipv d2 low batt. I changed the batt and resistance cannot get back liao. Try to lock...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.