Search results

Hello everyone!!! It's been a bit hasn't it. I am still around and still vaping. Been back and forth with analogs for a while but I think it's time to get full on back into vape only mode... thanks to CVS saying they will stop selling analogs in October. :| Anyway, still vaping using my two...

Power matters... What do I mean? I mean if you are going to vape, the battery you use can make all the difference. I started with Blu then moved to an eGo-T 650 then to the Vision 1300 spinner and finally onto the VAMO with two 18350's. With each progression the quality of the vape increased...

I decided to run one 18350 in my vamo last night. I made sure I charged them both. After resting my batteries I put it in 18350 mode, checked my watts then my ohms... 1.6ohm's. Odd. Today I decided to stack the vamo, put both batteries in, checked my watts then checked my ohm's... 2.0ohm's??? So...

These 18350's came with my VAMO... just wanted to know if any of you have used them and if so, are they safe. I haven't had any issues using them. They do last a good long while. I am running them stacked.

This thing is sexy!! I just got my Pro Tank in the mail today, thank you Myvaporstore. I washed it inside and out with hot water and let it dry. Checked the two coils on my VAMO and went with the lower ohms of the two... which says 2.6ohm on the VAMO. The other said 2.8ohm. I love how the logo...

I had the pleasure of going into Madvapes store earlier today and met the owner who is a pretty nice guy. They have a lot of juice there at the location near north Charlotte, North Carolina. The owner mixed a nice little sample for me and it's pretty good. Its a french vanilla mixed with peanut...

People seem to like "mechanical mods" and I have been looking at a few. I think I understand what it is and correct me if I am wrong... this is my understanding of what it is: A tube that holds a battery or two that has a momentary switch (on when held down/in and off when let up/out)...

I finally got around to getting my AGA-T2 up and running. The wick is in my opinion the easiest part to do. Using a large paper clip, straightened out, I wrapped the mesh tightly around the paper clip. It was a lot easier than I thought it would be. I used my butane torch pen and began torching...

I must say... I am disappointed. The vapor of the EVOD is great, the flavor is great... the leaking sucks big time. I used it for one day and it was so wonderful... fits supurbly on my Vision Spinner 1300 and matches the finish as well. On day two I noticed the draw was getting tighter. I paid...

I have a VAMO on the way and I am getting a parts/accessories list together so I can begin my "VV/VW Mod" journey. I am going to be using two 18350 batteries and an AGA-T2 RBA. I usually vape thicker juices but I will also vape thin juices. 1.8% or 18mg Nic. From my readings, I understand the...

3 clearomizers, 3 different set-ups, one battery, one juice. This is my comparison, my opinions and my test of these three "clearomizers". Ok, let me start off with this, these are different tanks. One is a top coil with a wick, one is a cartomizer tank and the last is a bottom coil with a...

I am going to be buying a VV/VW mod/apv soon. I will be going 18650. This will be my "at home" device... the one I am proud to look at, excited to vape on, and want the best performance from. My Vision Spinner 1300mAh and Vision Nova's will be following me to work as they are working very well...

I have cleaned this thing three times now. I have used cold water, hot water and boiling water. The taste is done. I am sure the coil is shot... well, maybe the wick because the coil still lights up big time. There is no burned looking wick though so I am puzzled. Well, this is why I bought it...

I am getting very little out of this thing. Less Vapor and TH than this juice has in my mini nova. I know that the carto in this has one small hole... honestly I am getting a lot of air. I would like to know from you all, do you think I need to punch another hole? What would another hole do...

I just got my Vision Spinner in the mail and I immediately put it on the charger. Now this is the exact same charger I use to charge my eGo-T 650mAh with no issues. I put the spinner on it and the button flashes like 10 times then goes out and the red light on the usb part of the charger blinks...

Does anyone know of a different end cap we can use on the mini nova's? Or if they are even made? I am not a fan of the cross hatches on them... sure they are great for grip but look crappy to me. I was thinking about something smooth? Chrome, Black Chrome or even aluminum.. brass... copper...

Well I have tried three samples of Halo... Thank you Cinder Ella. First impressions: I will start with my least favorite to the best of the three. Twisted Java - What can I say... I can't get the peppermint taste out of my clearo!! I have washed it, dried it and am now running my last batch of...

Hello all, I need some advice from you great minds out there. I use an eGo-T 650mAh batter and a CE4 clearo I believe. The power rating of this battery is perfect at this point for my vaping needs so I want to stick with a 650mAH eGo. I just ordered two clearomizers, both Visions. One is a...

I started out with my JCRO Domestic and was given a free 10ml Dekang Cappuccino flavored juice with my e-cig. The Dekang was spoiled and the smoke shop owner replaced it with no issues after he smelled it. I went with vanilla by Dekang and its great. Before I exchanged it I bought a 10ml bottle...

The picture you see below of my eGo-T and Clearo is how my girlfriend purchased it for me. It came with a free 10ml bottle of e-liquid (Dekang) 18mg cappuccino is what I got. The first half hour was great but once I got home the flavor started to turn... it turned nasty! I don't know what the...