Search results

I think 12mg is too strong with 0.6 ohm coil. But if you don't mind, could you tell me how long do you vape? And the nic level that you use before?

With my humble opinions: 1. Tighter airflow will give more TH. 2. Regular round wire coil usually give more TH than mesh coil. 3. Top airflow usually give more TH.

Both Asvape Hita Ink and Smoant Santi have no issue. They have no leak because of the design. Generally speaking, you should buy a device which has a separate air inlet chamber.

Maybe Smoant Santi is suit to you.

As far as I know, they use the same pod. V thru has a display.

I think the juice is too thick.

So, let it is easy to understand, maybe the IC that control charging on the device doesn't regulate the input in the right way. Am I right?

Thank you to let me know that I wrong. So the problem is there is something wrong with the resistance of the circuit board. This problem will made the circuit board draw too much current from the charger. Am I right?

I do not know how to explain because I am not a electronic guru. But you can imagine, you pull the throttle to make your motorcycle run at 120 Km/hour after that you pull the brake to slow it down to 60 Km/h but you don't release the throttle. Is your brake will be so hot? You provide 2.5A...

Is this problem start immediately or after a while? Can you give the information of the rating current of the charger that you use? Is your charging cable still in good condition? Before find out which is cause this problem, please, do not charge your device anymore. The connection when charging...

There is a RBA for Marvel pod by Hcigar. This RBA also fit perfectly for the pod of Smok Nord.

As far as I know there are two RBA for Smok Nord coil type. 1. Ruok RBA for Nord. 2. AFA RBA. Both of them have 510 adapter.

THANK YOU FOR YOUR GIVEN INFORMATION. MY DEVICE WAS COMPLETELY FAULTY. I THINK SOME ELECTRONIC COMPONENTS ON THE CIRCUIT BOARD WAS DEAD. MY LOCAL VAPE SHOP SENT ME ANOTHER NEW ARGUS AIR. I HOPE THERE IS NO PROBLEM HAPPENING WITH THIS NEW LITTLE GUY BECAUSE I REALLY LOVE IT.

@ArminF: Would you please to confirm to me that the format of the firmware is *.swdf? The software that they provide on their website just recognize *.zwdf format. I wonder if my device was dead by the faulty hardware or by the wrong version of firmware.

I am afraid so. I think I will disassemble it, try to use a copper small gauge wire to bypass the power button and made 5 times contact in a row to activate the device. Hopefully, it will turn on.Then, I can use it in automatic mode. But God bless me, where can I find a suitable screwdriver to...

Alright, I had a annoying experience with this small guy. I afraid that this problem caused by a faulty hardware, a faulty fire button. After I flashed the firmware, my device was off. Right now, there is no way to turn it on - again. PS: The device was normal when I use it in the first time...

Yup, I will try to reflash the firmware. The screen still not wake up eventhough I plug in the cable. Suck the pod to wake up the screen then replug the cable and the screen show me that the battery is charging. I really don't know if this problem cause by the software or the hardware.

I had an annoying problem with the Voopoo Argus Air. After I locked the fire button, I had no ways to access the device. 3 clicks in a row to change the wattage setting, nothing happen. 5 clicks in a row to access the sub menu, nothing happen. The device goes on standby mode after a few seconds...

I do not have this kit and the rba so I just give you some suggestions. 1. Juice feed hole seem too small, maybe you use high VG juice. Did you try 50/50 blend juice? 2. While it is fully assembly, look at the juice feed hole. Is the juice feed hole fully flooded in juice? Is there anything...

DID YOU TRY "DAM METHOD" ? TRY NOT TO PUT COTTON INSIDE THE JUICE CHANNEL, JUST COMB OUT THE LEG OF THE WICK AND LET IT SIT ONTO THE JUICE CHANNEL.