Search results

I also chose the Efest V2 but have been charging at 1 amp. What are the pluses of using the lower rate?

Hi all, I am considering the Ehpro kayfun lite plus, the Russian 91, aqua clone and looking others. Because the originals are more expensive (although Russian 91 price is steep for a clone), and hard to find originals. Any suggestions out there? I am using Kanger mini pro and aerotak and small...

Thank you BostonVape, This is helpful, now just need to decide which one to get, clone maybe.:)

I am down to 6mg from a start of 18mg over a year ago, and I am wondering if a Russian 91% or kayfun would help me down to 3mg. Right now I'm using the aspire coils and aerotank, sometimes evod or miniPT with cotton at 6.5W - 8W. But I'm not interested in subohm vaping. It seems that most people...

These are really helpful. Thanks!

I'm not sure what is meant by 'smallest' setting. There are no settings on the Aspire ET, although I believe that the Nautilus has airflow control. The ET is a much simpler device and uses different coils than the ones used by Nautilus. I have only built single coils, with cotton, and they are...

Sometimes the Aspire head start to give dry hits, then I draw on it with the air holes blocked off to suck more liquid into the coil. Which works ok, but I think the air holes may too small. I read about drilling out larger air holes in some tanks, and might try it. Do I need a special drill...

Another suggestion: get her an EVOD kit - comes with 2 clearos, 2 650mah batteries, a charger and 5 replacement coils ml . This kit can be goten at mtbakervapor with a free 15 ml botle of juice of her choice, all fo $39.95. Get her a few more Evod clearomizers of different colors ($4.95 at...

Thanks guys. Looks like I can't go wrong with the 19mm for my first one.

one more: are these tanks used with the MVP or vv gripper? If so, would the 15 mm be best?

Thanks much brooks and ocd. The vamo's threads reportedly are not so good. So I was thinking of using an air flow controller between tank and device to protect the threads. Any problem with this? Thanks in advance.

Hey guys, I've tried to search for an answer, but this is a LONG thread. Which size IB tank will go best with the vamo v5 with the slightly tapered top cap? many thanks!

Starting out with Blu e-cigs. If I had read more on ECF and done my research, I think I might have started with something better. Another: buying too much stuff - 808's, 306's, spinners, vv gripper, mvp, vamo... I could go on with cartos, clearos, BDC clearos, .. I think you get the picture...

Good point about the soldering. Maybe worse than inhaling an occasional burned cotton fiber or burned insulator.

To confirm, are these the correct grommets? AGA Series Positive Post Insulators - 10 pack - Kidney Puncher Where can I get non-resistance wire? Is there a particular type of solder material. I have some stuff that I have used on circuit boards, and wonder if that will work.

I recently started building coils for my protanks and evods, using 32g kanthal and cotton. I took 4 heads apart and noticed that one of the white insulators was burned on one side. If I reuse the burnt one, will it continue to have a burned taste? Or should I toss it? Thanks.

Ok, I got a Klein MM200 multimeter. Is this good for testing dry coils? It is difficult to hold the leads in the appropriate (+ and -) places. Thanks!

I am testing with a PV - VV gripper and MVP2. Yes, there is wick in coil - silica. What else?

thanks. I'm not using cotton, just silica wick. Should each wrap of coil light up at same time? Seems like one lights, then the next, then the next, and so on until all light.

When building a new coil, does it have to be tested with liquid on it, or can it be tested dry? I see videos where someone puts it on a battery to test dry, and I read somewhere else it needs to be wet. Thanks in advance!