Search results

All 3 Kennedys sold. 200 for the limitless mods and tubes. 90 for the osmium. 10 bucks off remaining atties

Bump, make me an offer. Will give discounts for multiple items

make me an offer...

Bump

afternoon bump

For Sale/Trade POSTING IN THE THREAD IS REQUIRED FOR FEEDBACK TO BE ENABLED Selling: getting out sale Condition: Good Known flaws: Shows signs of use Image: Description: Still vaping, but no longer collecting. Would like to free up some money so I can fund my other hobbies. Limitless...

Hundredths really isn't that precise... thousandths, maybe... but is it really necessary to spend $80-$300 if you're only going to be using it for your ecigs? It really isn't that convenient to have to use a multimeter to check your resistance anyways.. you need to know the resistance of your...

I think that depends on what device he is using... voltage drop varies with different mods, as I'm sure you know. Probably close to 3.1v-3.4v after voltage drop is my guess, depending on the mod. IMO you really don't have to worry about blowing your face off when sub ohming... People...

Search ophion coil or snake coil.

Yes, great atty. I've had mine for a week or two now, and haven't touched my Quasar much since I got it. I did grind off the airflow tabs, since I never use it and do centerpost builds exclusively. The biggest selling point for me was the ability to fit 2 strands of 22g through the center post...

Well naturally it's thicker, so it might wick a little worse, all depending on how you build your wicks. I've had 100% VG wick very well with solid 500 mesh wick, and other times terrible with an identical build... just takes some experimenting. Your 325 should be good, I would still consider...

You could also try rolling a smaller piece of mesh up and put it in the hollow part of the wick (really only needs to go down to about the deck) so that there isn't so much juice sitting underneath the coil. This would be easier than pulling the whole thing apart, and would be easy to remove if...

Yup, name calling... Real mature of yourself. I'm 25 years old. Do you even know how long it takes an 18650 to go thermal? It's not like a short fuse on a firecracker. Go do some research yourself. I made sure that if I did vape, I was far enough away from other people, in case it did go...

Yup, was ready to chuck my cronus if it started to get hot. It was obviously right in front of my face, since I was vaping it. Battery safety isn't something I take lightly, but sometimes you run out of charged 30 amp batteries and feel like pushing the limits. Don't give a .... if you call...

Yup, I know how to do math, was fully aware the dangers... Was paying attention to the mod the whole time, button never got hot... Don't take a condescending tone to me. I wasn't recommending it to anybody, just said I did it. EDIT: I guess YMMV could be misconstrued as a suggestion to try...

Hey, you took something and made it vape the way you like... Nobody can fault you for that. Thanks for the kind words

P.S. that looks like a steam turbine, not a kraken?

I use cotton exclusively in my drippers.... cotton just wont keep up with the resistance I vape at in Genisis tanks. I prefer SS cable with a mesh sleeve. Easy to clean; rinse my tank, dab wicks dry with paper towel, dry burn, rejuice and vape away. Re-sleeve my SS cable every two weeks, but...

I run a .28 ohm dual on my Kraken with Sony 30amps, still got my face.... I've run the Panasonic CGRs with .18 ohm dual coil on my drippers with no problem, not the smartest but the batteries were fine. Warning.. This is well over the amperage rating for the CGR cells, and could result in...

TrentTC dropping some knowledge... great tips. As for the hot leg... poke the top wrap up and down, you are shorting where the hotspot ends on the wick. Worst comes to worst, toss the coil, pull your wick, torch it, and re-wrap... you want it snug on the wick, but not choking it. If you end up...