Search results

The DaVapes clone switch is exactly the same design as the real poldiac except the contact screws that go into the double screws are not reverse threaded. This will cause the contact screw to "screw in" when an atomizer is screwed down. The clone switch parts are not of the quality of the real...

The "DaVapes" poldiac clone tubes and pants will work if you can find one of them. I have one of the DaVapes clone poldiacs that I put all the factory MMV switch parts in and added a factory top cap. This was back when the poldiacs were costing $250 and I did not want to carry one of my two real...

I for sure am going to have to order one or two of these tanks, if for no other reason than to show my support and respect for this great design. It sure seems like the perfect tank and I like everything I am hearing about it.

I have been a member of this forum for the last two and a half years. I have not posted much in the last six months or so, but I visit the forum everyday. In the past I posted a lot in the original Kayfun thread and the Poldiac thread. Roxy became one of the most knowledgeable members in the...

Roxy, How does the flavor and airflow compare to the Serpent single coil rba? Can the HIGO be used as a single coil? I was thinking of getting the Serpent, but I like the looks of the HIGO a lot. I use my Aromamizer daily and the HIGO looks like it may be even better........ Any coupon codes...

Sounds like the contact rod is not making contact with the top pole screw if you have to push hard on the top edge of the button. With the contact rod being a snug fit in the button and the pole screws screwed fully down tight there is no movement for the contact rod to make contact with the two...

One major problem that can show up with dual coils with temp control is the clamping of the wire in the post holes. If the atomizer uses a common hole for two wires, sometimes one wire does not get a really good connection. One wire crossing over another wire in the post hole will always be a...

I too think the outside of the RX and the Reuleaux are the same except for the location of the window for the screen which is higher/closer to the fire button on the RX. The local vape shop I hang around at just got the RX in today. I will try to compare them to my Reuleaux early next week when...

You got me thinking about the problem with the recessed well around the 510 on the RX and the Reuleaux and it causing the barrel on the Sub Zero to be loose. I took another look at the problem and I have come up with a fix. I used the lid off of a plastic tub like what is used for butter or cool...

I received my Sub Zero rda today and after giving it a good cleaning I built it with dual 24ga 317L stainless steel 3mm coils which came out to read .24 ohms. I did have to add one thickness of flat dental floss under the oring on the base to snug up the barrel so the air flow adjustment would...

Yes, Miriam is a sweetheart and very helpful to the customers. I have really enjoyed my OverOne rda and I think I am going to put a TC build in it tonight for the first time. It is really a flavor machine, holds a good amount of eliquid and has top notch machining. You can close down the airflow...

What can happen with some Poldiacs is that you can not tighten the pole screws (the two screws the contact pin touches) much beyond finger tight. If you tighten them too much with a screw driver they can "tilt" just a little and the contact pin will not make full contact with them. Remember...

Greeneagle, you will getting a really nice mod from MMVapors. Jim and his people at MMVapors are great and care about their customers as you say. I have two of their Poldiacs, a Nanos and an OverOne rda. I wish they still made the Poldiacs as I think they are almost a piece of artwork.

Thanks Mr.Mann for posting the ecig.com coupon code. I just used it to order a Sub Zero rda from ecig.com and got it coming to me for $43.19 shipped. I was going to order one for a friend also, but the site would only let me order one.

I now only use TC mods and have four of them. A IPV4 (first, but not using it now), Hcigar VT200, Relo DNA200 and a Yihi J board dual battery box mod I built. I am getting ready to build a small wood, two battery, DNA200 box mod. Going forward I will only buy a TC mod if it lets you enter a TCR...

Madness RDA Has anyone seen the Madness rda that is now available from Atmistique that is shown in the above link? Bottom airflow as well as top airflow(can be closed off), can be built with single or dual coils, regular or chuf type drip tips. Cost from manufacturer is 87 euros. Below is a...

If you have contact pins for your poldiac that are the silver plated ones or the rhodium over silver plated ones and the coatings have gotten in bad shape on them you can get them recoated with rhodium at a lot of jewelry stores. They rhodium coat silver jewelry all the time to keep it from...

You can rebuild the coils that are used in the Kanger small tanks like the mini Protank or Evod. There are videos showing how on YouTube. I did it a few years back using 30 ga wire (I think this size) and the Peaches and Cream yarn from Walmart.

I just tried this method and I must say it works like a charm.....perfect. Thanks for passing this tip along.

If a battery with a bad wrapper is installed in a mechanical mod correctly (positive battery pole to 510) if can cause the mod to go into a "auto fire" mode because the exposed area in the wrapper can complete the circuit and act as the switch. This condition will not cause a battery to "vent"...