Search results

  1. highping

    My Atty Resurrection Method

    You are correct. Dry burning is the best for removing that burnt taste... the "video" part threw me though. Apparently, someone out there made a video of this method (?)
  2. highping

    Tutorial: Juicebox for around $8

    I just have to say that I LOVE that this thread is still getting traffic after all these years. It makes my day whenever I see that someone new is going to try it (or has already built one) ...even if this mod is somewhat obsolete now. These days there are tons of commercially produced ecigs...
  3. highping

    Tutorial: Juicebox for around $8

    The bottle/atty connector assembly is identical to the one in this tutorial (only with a bigger bottle i think). I just soldered a couple pieces of copper on the other ends of the wires for the "switch"... and by switch, I mean mashing the two copper plates onto the ends of the batt with your...
  4. highping

    Tutorial: Juicebox for around $8

    xrob: here's one I made for the 18650... http://www.e-cigarette-forum.com/forum/modding-forum/74240-my-very-basic-510-juicebox.html I just used the box that the batteries came in ;)
  5. highping

    My Atty Resurrection Method

    Thanks ZipJim. It's great to see this is still helping people over three years after I posted it!
  6. highping

    My Atty Resurrection Method

    Sounds like your battery may be dead...just recharge and try again. Edit: just realized this was from Dec :blush:
  7. highping

    Tutorial: Juicebox for around $8

    Good build xLowEndx! It's great to see that ppl are still making these (and posting pics!) Also wanted to remind everyone that wants to make one of these to skim through this thread first...http://www.e-cigarette-forum.com/forum/modding-forum/97828-brass-juice-2.html
  8. highping

    Brass + Juice = :(

    Just wanted to give this thread a little bump to keep it close to this thread... http://www.e-cigarette-forum.com/forum/modding-forum/95728-tutorial-juicebox-around-8-a-7.html
  9. highping

    Tutorial: Juicebox for around $8

    Nice builds ruledo :thumb: ...the horn switch seems to fit well... i like the custom stickers too :)
  10. highping

    My Atty Resurrection Method

    I have not yet tried this on a tank atty and I'm not sure how well it will work. The problem I see is that the wick comes out the top (through a little pipe) and will never be able to be heated to a high enough temp to 'ash' the stuff in the pipe. It will however (probably) get the wick in...
  11. highping

    My Atty Resurrection Method

    :thumbs: I don't know why everyone tries to over complicate this method with alcohol, mouthwash, soaking, boiling, etc, etc. ALL that is needed is tap water, electricity and about 10 minutes (more like 3 minutes once you have it down) ;)
  12. highping

    Tutorial: Juicebox for around $8

    I actually drill the dropper to allow the pipe to slide through it and then leave it on the bottle. It may not be necessary, but I think it helps with the seal between the bottle and the cap. Without it, you may (or may not) get leakage from under the cap. BTW: nice lookin' box Hogwart :thumb:
  13. highping

    Tutorial: Juicebox for around $8

    Mickyrat: Yes, I should have mentioned that. I wish I could edit it into the original post, but you only have 48hrs(i think) before it's 'carved in stone'. Harry: you just unscrew the bottle and fill it.
  14. highping

    Tutorial: Juicebox for around $8

    That's a much better idea than what I said :thumb:
  15. highping

    Tutorial: Juicebox for around $8

    Hacksaw blade or dremel with cutting wheel. wheels are cheap...dremel not so much, but there are infinite uses for a dremel, and you can pick one up for under $20. You could use wire cutters on the end that goes in the bottle, since it doesn't have to be perfectly round. Just leave the...
  16. highping

    Tutorial: Juicebox for around $8

    An 801 might work pretty well with this; it will take a bigger tube though. 801's hold a ton of juice, so you will probably not need to pump nearly as often as with a 510. 801's (IMO) also work much better at 5V, so you might want to use a 3-batt box and either put two batts in series or get...
  17. highping

    Tutorial: Juicebox for around $8

    Looks good Micky :thumb: As long as it vapes, it's a successful mod! I've always been a 'function over fashion' kinda guy anyway. As for the needle depth... It looks about right to me. I have made a few of these now and I still always think it's sticking out too far when I take off the...
  18. highping

    My Atty Resurrection Method

    I'm confused. If you are seeing orange, then you did not 'blow' your atty...you just cleaned it :) When you are done with this process there should be no vapor. Again, that just means it is clean and dry. After you have done this method (and have orange glow and zero vapor), you have to...
  19. highping

    Do Not Order "Free Trials"!!!

    I never thought this thread would grow to 1000 posts when I started it. Wonder how much $$ has been lost by some of those companies as a result. :) ...they're still at it though...and more than ever :rolleyes:
  20. highping

    Tutorial: Juicebox for around $8

    Nice lookin' build warmturkey. Thanks for posting pics!
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu