Search results

This looks interesting, it appears to be a boro alternative?: $8.90 SXK Unit Tank for SXK Supbox / Supbox Pro / SXK BB Box Mod Kit - 5ml / acrylic at FastTech - Free Shipping

It's about 3am in the UK at the moment, chances are they'll reply in a few hours..

They look legit, I checked their address with Google Streetview, they have a real shop in the UK... Royal Mail to Australia is usually fairly good, not sure about to the US though, and with Covid... (Royal Mail is the UK equivalent of USPS) Their prices are a bit high compared to China, they...

Heads up: FastTech 8th Anniversary: 15% off Site-Wide Coupon Sale Code: FASTTECH2020 https://www.fasttech.com/forums/promotions/t/3096184/coming-soon

MECHLYFE Link 510 Adaptor for BB 60W/70W /Billet Box Mod Kit $8.17 MECHLYFE Link 510 Adaptor for BB 60W/70W /Billet Box Mod Kit - 304 stainless steel at FastTech - Free Shipping

510 Thread Adapter Connector for BB = $6.51 $6.51 YDDZ A2 510 Thread Adapter Connector for BB 70W / DNA 60W Box Mod Kit at FastTech - Free Shipping It seems to be a new version of this:

You are most likely right, I just noticed the manual shows LiPo above the 3.09v... I went with 3.2v because I use 10 amp Sony/Panasonic NCR18650GA's, I only vape around 10 watts, they drop off real fast once they start getting down, I figure not dragging the crap out of them may help extend...

New on 3F & FT:

Checking mine, the "Cell Soft Cutoff" is set to 3.2v, but I think I changed it, looking in the Escribe manual it shows 3.09v, so that may be the default... From the manual: Cell Soft Cutoff: When the battery gets low, the DNA will prevent any cell voltage from dropping below this level. I'm a...

When I install the Xeta in the boro I just press the top end of the xeta against something solid like the side of a table to force it to the bottom of the boro, if you just rely on the 510 nut/key to push it down sometimes they dont seat down onto the o-ring all the way and they leak...

I never bothered trying the Vape Shell because of the size of the chimney, it looks way too big for real MTL, I very much doubt it would suit me... I've found in the past for my MTL style I need tanks/devices that are fairly restricted all the way through, not just DL style devices with the...

I use fairly tight MTL with the Xeta, I use the smallest lower airflow insert under the coil, I think it's a 0.8mm single hole, I ran a 1mm drill bit through it by hand to open it up a little, and I use the medium sized chimney insert, I find it great like that... (I vape 1.8ohm 3mm coils at...

FT 10% off for the 4th of July: Best Fourth of July Sale 2020 Happy Independence Day! 10% OFF Site-Wide Coupon: FastTech Forums

lol, all good,... To celebrate I just ordered another 5 years worth for the stockpile, lol

Yep, looks like we're all good till Jan 1st 2021.. The official media release: Prescription Nicotine Based Vaping

There's talk around the place they ran out of 100mg freebase and substituted it for nicsalts, and they haven't warned people other than a message on Reddit, that sounds sucky for non-pod users that are chasing the throat hit :( We don't have any more 100mg freebase unfortunately :( Had to swap...

It sounds like all their orders are getting through ok so you should be fine... Their final sale will apparently start at midnight and it sounds more like a stock-clearance: Yes, the only products that will be available are packs of pre-bagged pre-made juices – both imported and Aussie/NZ...

These guys claim they're going to do one last batch that will get here before the 1st: Vapoureyes NZ In the next few hours this site will re-open and you'll have one final opportunity to stock up on nicotine juice before the ban takes effect. We've arranged a last-minute cargo flight from New...

Yeh, don't worry about those rejected messages and such, especially with DHL, it seems to be a glitch in their system and that often happens... and once it's cleared Customs it's all good :banana::headbang:

From the couple of photos it almost looks like too little heat so you've had to apply the soldering iron for way too long and the heat has then heated up the whole wire, track, and such, the solder hasn't flowed too well... I'm no expert and I'm a bit rough but I've done plenty of soldering...