I was still fighting a leaking 316 FT KayFun 4 until a friend brought over his EH Pro KF4 that number 9 had loosened up on. I swapped out number 17s still with the old o rings on and that fixed the leak on the 316 and the EH Pro does not leak either. 10 hours later and not a drop has leaked from...
I had it apart again today. I am pretty sure 1-11 is in pretty good shape. That said parts, 3 and 5 have some side to side play that my FT A does not have. I guess I could swap top caps (34-40) out on them and see if it cures the 316 and makes the FT A leak. I left it at work today, I still...
Yes, I have a bag of 50 12 x 1.5 orings. I have a FT version A as well. It leaks. I also tried 10 wraps of cotton thread and then an oring but it was too big. Unwrapped it to 5 wraps and still too big to fully open JC. Looking at the diagram maybe I will try to replace 18 and see what happens.
So on the third day of use my FT 316 started leaking out the air holes. A quick search told me number 9 might be loose. I took it apart and it was slightly loose, about 1/4 of a turn. Put it back together and it still leaked. Replaced number 16 oring. Seemed to work fine for a hour or two. Laid...
The FT 316 version came in today. Came in fairly clean, so from the post box to vaping in less than an hour. It is very nice. Juice control works much better than FT version A. Nice machining, but not perfect as there is a small blemish on the mouthpiece. I am very impressed with this clone. If...
A few days ago I wanted to change my wick and when I took the tank off I noticed my congestion ring was gone. Not sure how long it has been away, probably 3-5 days, but vaping fine. Just took a look at evcigarettes.com and they have it for $3 with $9.75 international shipping. For a few more...
In Germany I saw some "Power Smoke" base that supposedly has better vapor than a straight PG/VG mix. It was 10% water added to a variety of PG/VG ratios.
OK, I finally got my order in. OoO shipped quickly, but the postal service sent my package on a slow tour.
Here are my impressions of the 4 flavors I ordered. All 4 mixes are four days old as of the writing.
I mixed all flavors in 50% PG 50% VG - 12 mg base
Cinnamon Churro- Mixed at 12%...
Hi,
I gave my Fasttech revision A a rebuild tonight. Went ahead and replaced o-ring 16 while I had it apart. Decided to check the tightness of 9, sure enough I was able to tighten it a quarter of a turn. I then took it all the way out to inspect it. I could not see much with my old eyes so when...
I did not finish the order. I was able to send a message via facebook asking about the shipping charge. If I do not get an answer tomorrow I will try to call them during business hours.
Thanks for your help.
I thought I would give OoO a try and although I could not find anything about international shipping on the site. I gave it a try. I ordered 4-10 ml bottles for about 14.40 but with a whopping 43.50 international shipping charge. Shazam! I think if an ebayer in America can ship a Kayfun 4 Clone...
I guess I will give it a go. I have a friend that has a simple soldering iron. Maybe he will help. Anybody know whick fatdaddy 51o is best on this clone. The V4 mshort or V4 Low Profile?
Thanks
Never mind. FDA suggests the V3 wood and I added the 22mm washer.
Thanks, but I am not having any luck getting it to work for more than a few hours at a time. I guess I could order out a Fatty Daddy 510 connection, but the Cloupor is so full of hot glue that I think I will have more problems. I do not know how to solder. I guess it is time to start thinking...
Hi,
I have an Cloupor Hanna clone that is about 6 months old. Here recently I am getting a few "Check Atomizer" messages and I crank down a little harder in the atty to make the connection. I had a MVP that would do this and I was able to tease out the center pin with a mini screwdriver. So far...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.