Search results

Well wether the atty can use 100% vg gonna come down to the wicking and juice feed inlets/holes of the atty..... ANY COIL can be used in BYPASS... the build of the individual coils used will determine if it can produce good vape on battery voltages. OHM AND CHARGE WILL DETERMINE WATTS.. type...

If the store has a hardware or auto supply store they probably have battery wraps..... they will be package as shrink wrap for wiring. Sent from my SCH-I605 using Tapatalk

You are right on the sound wrong on the rest. ... Boil a pan of water.... that what you coil is doing to juice... goal is a nice simmer rather than a rolling boil with big bubble of popping fluid.... those pops put juice in your mouth... instead of steam. Not keeping you atty clean or saving...

Popping is only bad if it results in burned lips from the splatter that results from the pop.... goal is to make the pop more a sizzle. Sent from my SCH-I605 using Tapatalk

The ability to provide desired vape with restricted air draw. Sent from my SCH-I605 using Tapatalk

Well here's the problem. Dtl and mtl do typically work on the same coil builds or at the same wattages..... Yes you can get a drip tip with a small ID to reduce flow more than closing airflow on a tank or if tank is not adjystable.... but less air means if the build was for DTL ypu might...

Trying to vape cannabis..... didn't work.... found it did do a good job of replacing cigarettes. And works for extract. 100% smoke free since 2015. Sent from my SCH-I605 using Tapatalk

Ohms too low means the coil is shorted.. and giving a low ohm reading.... coil probably touching in side the tank or head.... Sent from my SCH-I605 using Tapatalk

Also some juices are dirtier than others..... the darker the sweeter the dirtier the wick gets.. then the coil gunks up. Could try rinsing the heads out... might extend life a bit. Sent from my SCH-I605 using Tapatalk

You DO have a squonk pin installed in the atty? Sent from my SCH-I605 using Tapatalk

Well it seems to me you batteries have lost a third of their capacity. . I would replace.... As to 26 vs 20 series batts.... I would use the one I can get easier and like to use more.... but note I don't vape at above 10 amps much so CDR not issue for me. You sound like you prefer the...

Less than a month full charge 4.2 is ok..... more than a month drain to nominal voltage. .. 3.7 volts.... In either case you may need to recharge before use. Sent from my SCH-I605 using Tapatalk

Buy them a gift card so they can buy the vape..... Vape preference is too personal. Too much variety.... unless you know the device even type of juices they like .... we can't really help. CIGARETTE STORE SELL 20 to 50 brands of smokes for a reason. Sent from my SCH-I605 using Tapatalk

You do realize the juice and wattage choices you make have much more affect on coil more accurately wick life in any tank or atomizer. Dirty sweet juice and long ramp times make gunk. Not the design of the tank. Sent from my SCH-I605 using Tapatalk

I use my nectar in 18350 tube mech.... but prefer to use 18500..... the extra run time is more a benefit than the 1/2 inch of length. .. Last time I used 18350 was stacked series... Fact is anymore I run my tube mech as 18500 regardless the atty on top..... I rarely build above 10 amps draw...

If you order from China. .. doesn't really matter which company.. plan for delivery to take 2 to 6 weeks.... plan for tracking to be days behind reality..... item may deliver before track shows leaving China. Fasttech is a good vendor... Just slow. Sent from my SCH-I605 using Tapatalk

Bad coils happen all the time...... I averaged at least 1 bad coil in 5 before I started building my own.... not had a failure since. Sent from my SCH-I605 using Tapatalk

I'd buy the longer ones.... easier to cut to size if too big vs Making something longer if too short. Sent from my SCH-I605 using Tapatalk

Both could be correct if one wrap is thicker than the other or a tighter tube. Sent from my SCH-I605 using Tapatalk

Sounds like you just need some ZERO nicotine juice and any device that you can put it in... Your issue isn't the device... it the juice options. Sent from my SCH-I605 using Tapatalk