Search results

I am ordering some of these from Fasttech with the long tip SKU 1613409. Will need to search for some poly tubing once I can measure the bottom opening of the cap. Hopefully the tip will be right length. Also, I found cutting the bottom of tube in the Wraith bottle at a slight angle helps with...

Done Thank you

It doesn't look like the new Pulse 80 is going have the Gene chip. Voopoo screwed them.

I don't know sounds like VooPoo screw Vandy on the chip and going to copy the Pulse 80 Mod.

I just picked up a Wraith and put a Pulse 22 on it and it's terrific. Running a .45 Clapton at 40 watts and I go through 2 batteries a day. I vape all day in my office on 1 and 1 when I get home at night.

If you haven't found any try here Buna-N 70 : O-Rings - The O-Ring Store, We make getting O-Rings easy! they have 11.5mm and 12mm. There is also different thicknesses. 1.6mm etc.

Take your coil out and see if the air chamber below the coil is flooded. Dry it out if it is. Put a paper towel over the top of the coil and blow it from the bottom. I have found this to be the problem when the vapor drops if it isn't a bad coil.

Thanks I ordered a couple. I have been running my clone without the #4 for awhile. It works but hopefully these replacements will make it right.

If you change flavors a lot you may dedicate a few coils into categories. Bakery/Dessert, Tobacco, etc. and use them for flavors in the same category. I found that changing a few flavor types with the same coil can cause the flavor to go flat.

I paid that much for 4 of them from an eBay seller in the U.K. because I didn't know what size they were. Should have them in a week.

I have gotten some occasional minor seeping after a fill and gurgles sometimes. Quick wipe with a tissue and all is well. Not enough of an issue to take it apart again. If it continues to weep while your using then you may have nicked #7 O-ring.

I took the build deck completely apart to get any oil trapped underneath the insulator and in the screw holes

I am running a 1.5 build at 10.5 watts and compared to my Nautilus this thing eats juice like a Big Block Chevy. I don't know if the difference in flavor is worth the juice expense.

I saw one review on YouTube for the Infinite variety and the box had a magnetic front flap. I believe the reviewer bought it from a USA supplier for $45.00.

Thanks I didn't know what size I needed so it the seller made it easy. I will look for some of the ones you recommended and see which works best for me. The ones I ordered coming from UK so it will be a week or two before I see them. Maybe I will drive up to Wisconsin to see if I can find some...

I found these on ebay and have ordered a set. Ultimate Kayfun Deck Screws The cheap Phillips heads that came with my clone are a real pain to trap the wire consistently. Hopefully these will simplify it and I like the socket head torque without stripping.

You really need to get that bottom assembly apart there is a lot of surface area to hold the machine oil and your air is passing through there. When you remove the 510 the 10/11 part should fall out. Then you can get a screwdriver on #9. I put my parts with the O rings (removed) in a bowel...

Take a look at kayfunmods.com you might want to try using the air adjustment screw as shown in lieu of the spring.

Take a look at kayfunmods.com you might want to try using the air adjustment screw as shown in lieu of the spring.

I have been lurking this forum for a few and decided to join. A lot of interesting info. What I did completely by mistake was I reassembled the device and omitted the A7 spacer. All my binding and erratic ohm readings went away. The only thing I noticed was when the juice control is closed there...