Search results

i was just thinking about this post last night and forgot how to turn it into a dripper! thank you for bringing this thread back up :-) i like tight barrel drippers b/c they seem to be much for smooth vaping than a 22mm dripper. this should be perfect and much easier to use than my old...

got my stainless copper clone yesterday and i love it. $15.58 one at FT. i had blazing hot button, tube, atty and it turned out to be the positive pin wasn't out enough. to test my atties, i use an ego to 510 adapter on top and screw my atty in. works great. hits harder than any mech i have...

is the top cap spinning? if so maybe take the drip tip off to get a good hold on the origen > press down and spin your zna 30.

in my limited experience i would say so. i got an Igo-M and don't care for it at all, no matter what coil i build. it's a 22mm rda. Like you, I keep going back to my single coil Phoenix's for that "ooh that's it!" vape ;-) In the market now for a single coil rda now. I don't know that it's...

omg thank you for this post!! i remember reading about turning a kayfun/91 into a dripper before i got mine and it's working for now as a tank, BUT I have been disappointed with finding a new dripper for single coils that aren't super airy. your fix would make a perfect new dripper for me :-)...

thank you tayone. yes i have decreased my nic down to about 6. turns out i have a bad case of bronchitis right now, so the Igo-M is on the shelf. still can't get that thing to build right. even straight no nic VG isn't vaping right. Could be a clone malfunction in the design. I got it from...

thank you! i will try that also. i had to stop and think where i place my dt. on the side is cooler on my phoenix that i tried just now. i really love my original phoenix clones. great flavor, easy coil. i need some larger air holes, but my husband's smallest drill bit made a hole so huge i...

thank you guys for all your suggestions. i really appreciate the help. the first coil i put in the M was a slanted coil but it was solo. i know how to slant them so i will try that setup next with lower nic. when i take my drippers to the local vape shop they can't vape my high nic no matter...

larger bore drip tip is MUCH better!! thank you!!! i'll cut my nic and go 100% vg to see if i can get it even smoother.

thank you tayonne. some very good points. i didn't think about the drip tip. i have some larger barrel ones that i'll give a try. I've been dripping for about 3 yrs anywhere from 36mg down to an average of 12mg, so i think the harshness might be the drip tip. if i can't get it right, i'll...

I'm new to this. My 2nd try with 24g A-1 > 5 wraps > .3 ohm dual on my Igo-M. Using a sony 30amp battery. Got some knurled thumb screws from Fatdaddyvapes.com and now it's heating up fine versus the stock screws. I seasoned the coils by heating and squeezing. No hot spots on the coils...

I love reading all your how to's and seeing pics of your builds. I ordered some M2 knurled thumb screws for my Igo-M to try again w/ 24g kanthal from fatdaddyvapes. Hoping it will give better contact than what i was getting with the cheap screws that came with it. Only $7 and change for a...

Efest Battery Case Zip Up with Belt Hook Holds 3 18650 Batteries US Seller | eBay This hard shell battery case is killer. No more dealing with broken plastic 18650 cases, or having them open up on me. I can put this in my purse or glove box when I'm out. Handy little accessory for only...

Took my IGO-M to vapor hut and they rolled me a new dual coil @ .5 ohms. no more hot Sig 19 and it vapes good. The coils are closer to the posts than the center block and duh me realized just turn the huge IGO-M holes over to that side ;-) voila = i like it! I'm going to take my 24g wire up...

ouch! maybe you can trade some of it for a higher gauge. that's why i buy my kanthal at tempco. i got 25 ft for $5.29 and free shipping. Kanthal Wire 24 Gauge RW0248 - 25 FT 0.39oz Series A-1 Resistance AWG It's easier to buy small rolls to see what works for me. I used to use nicachrome or...

thx SL. I'm going to wait until i get my russian and see if i like that better. i do like dripping though. been vaping for about 5 yrs now and have been making my own juice for about 4 yrs. there are SO many new devices out there from the past year that i've been out of touch for awhile on...

I added a second coil tonight. both are about .4 ohms. using my sig 19 with a sony vtc4 30 amp battery and it's still slow to heat up and the mod is getting hot. I took the battery out and the battery is not hot = just the stainless mod. I'm going to tear all that out tomorrow and start fresh...

ps- the thing that scares me about mech's is hot button and blazing batteries. i had it on my p18 and until i fixed the spring with a wire leg, i was getting it on my sig19. i'm kind of a chicken when it comes to that lol. i used to have to fling my P18 across the floor of my truck will...

ok i can see i wouldn't be able to vape .5 dual coils on my 20w device. says it would need 35 watts? would have to use it on my sig 19 mech. i think it's probably time for a cheap new mech for efficiency.

very handy SL. took me a few to figure it out and i left some of the unknown fields blank, but it will be very helpful! thank you