Me being a step child and having step children of my own the burden is quite difficult... If you don't mind me prying what exactly is the depression stemming from? Having step kids or the size of the family... I'm just trying to grasp your concern before I offer my advice and try and help you...
Sounds like a wicking issue... The rba for the tfv4 is tricky to wick...so if you don't practice then you will be getting dry hits. The best way I have found is to put the cap on and cut at the lines imprinted on your wick... And cut them at a downward 45 degree angle so that only a tip of the...
I hate the zephyrus...very tiny build deck once you screw the base of the chimney on it doesn't allow for any coils other than regular single wire...claptons end up too thick and short out... I've been building for quite a while and the zephyrus is extremely frustrating and frankly just sits in...
Notice how the coil opening is centered on the screws. This is a 2.5mm ID that seems to be the sweet spot.Plenty of cotton running through the coil enough for gradual resistance but not enough that your cotton is pulling apart as your pulling it through the coil. Tails go up through the coil...
Standard coils or the rba? Most times if a flooding is occurring you are priming too much or not vaping the tank empty before a refill... If your coil is still saturated and you refill the tank...the vacuum caused by putting the lid back on will force more juice into the coil flooding it.... A...
Of course it is possible the problem lies in the coil being able to wick efficiently at a high enough power to give you a pleasurable vape...you won't be getting 5 second pulls on a 75 watt load without a dry hit that I can assure you. Juice is just too thick to keep up with that style of vaping.
Notice how the coil opening is centered on the screws. This is a 2.5mm ID that seems to be the sweet spot.Plenty of cotton running through the coil enough for gradual resistance but not enough that your cotton is pulling apart as your pulling it through the coil. Tails go up through the coil...
Try taking a q top and some rubbing alcohol the the 510 connection on your mod... Sometimes if it gets dirty or has residual juice down in there it can give you a false reading... Everything Is now pointing to your 510 connection on your mod.
From the pic it looks like the excess of the leg on the left side is touching the coil nearest us in the pic causing a short in your coil closest to us which you can see somewhat in how the Browning is producing on the left and right side of it. Try loosening the far side coil and pull that leg...
2 strands of .5 kanthal ribbon twisted together and then twisted that product with a strand of 28ga nichrome. Dual coil build of 8 wraps 2.5mm inner diameter.
Ok so don't get side tracked with the screwdriver rba and cotton those all go together exclusively. The rba stands for rebuildable atomizer essentially what your 1.2 coil is.. It is a casing for you to build your own with your own wire and cotton. That is a more intermediate vaping hobby that...
Yea perhaps you need to work on your draw technique to allow for you to take that long of a pull to alleviate your dry hits... I always take 3-4 seconds but I also vape at a lot higher temps.
General consensus here is no since you bought from a local store....however be warned that the TFv4 tank with the RX200 has known to cause issues with damage on the mod. They even had a press release specifically naming that tank as one that damaged the mod so do be careful when utilizing that tank.
what is the inner diameter of your coil... i have never had a dry burnt hit on my aromamizer and I vape anything from regular kanthal coils to claptons all the way up to 90 watts. It is wicked exactly as you would a dripper tuck the tails under the coil and leave a pocket under the coil for air...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.