Search results

So I have a dual coil .25 build that was vaping beautifully...after about an hour the device is reading it as low resistance. Cutoff on my mod is .10 Any idea why this happened and what I can do to fix it?

Hey guys, so I have some alien clapton wire which is great, but as I’ve mentioned in another thread, I need a significant amount of wraps just to get it to ohm out above my mods restrictions. I’m looking for something where I can wrap a dual coil 5, 6 wraps and have it above a .20 lol, anywhere...

So when I went to dry fire my coils to get out the hotspots, there was a small, quick spark, then everything was fine. Has this ever happened to anyone? Is it normal? Should I throw away the RDA?

So I bought a spool of alien Clapton’s which are gorgeous, however I need quite a lot of wraps in order for them to ohm out above my mods restriction. My question is, is it okay that the coils are wider than the slots of the air flow? I don’t know if that’s going to affect flavor or not

So I have to be honest, I love my Drop, but it’s just a little too warm if a vape for me, so I’m thinking about getting the Dead Rabbit...just wanted to see the opinion from those who have tried both, is the Rabbit also a warm vape? I mean I prefer a warm vape, but not warm to hot as the Drop...

So I just ordered a spool of alien Clapton coil....realized that it is stainless steel. I heard somewhere stainless steel is specifically for temp control. Should I cancel the order before it ships or power mode is okay? Here’s the link if interested in what I bought...

Heyy has anyone noticed on the Drop that it is VERY easy to twist for your airflow holes, I’m talking like no resistance at all? I’ve never had an RDA with such ease I feel like it should be a little more resistant...or is this just how it’s suppose to be? Like the center cap is so lose that...

assuming it is. I installed a premade dual coil that was suppose to come out to .22...and it was at around .80. I decided just to put it on my mod which is reading it as a .25 Are these coil master mini tabs the most reliable source? I feel like it’s probably a better idea just to use my mod...

Like on a 4 post system, am I suppose to put the leg that rolls over into the first post hole, or the leg that rolls under...does it matter?

So in another post, someone was mentioning that he could build a .2 dual coil that would be great around 30 watts, and then another .2 that would be great at around 70 watts. I’m just starting to build coils, and I know this has something to do with mass, surface, diameter, etc...Basically I’d...

so when using ohms law on a regulated dual 18650 series mod, should I be putting in 8.4 for volts on the ohm calculator, or stick with 4.2? And for whatever the answer, why? Thank you. Or should I not even be using ohms law for a regulated device. Ugh ‍♂️

Question is just along the lines of why people prefer mechs over regulated. I originally thought that it was because people can use lower ohm coils, but after researching and watching mooch’s videos, I realize that I can run the same builds on a regulated device, since ohms are pretty...

I did a thorough search on the forum but all I seem to find is if people are putting too much or too little of cotton, and my question is more about how too much or too little affects flavor. I just did a rebuild and put a lot less cotton, well not a lot less, maybe 1/4 less of what I’ve been...

Hey everyone. So I am completely aware that the voltage display on my regulated mod is the output voltage of the regulator and NOT the battery voltage. That being understood, am I still suppose to be within a range there? I am using a dual battery device in series, a 0.23 dual coil build...

So I have a regulated series mod with 2 HG2’s in them, a 0.22 dual cool build, and it bakes great, but every now and then the screen says “short”. Not sure why this is happening I am well within the amps limit that these batteries can handle. Can someone explain what might be happening here?

So I LOVE the SZX Competition mod from Sub Ohm Innovations, however after doing much research it seems that the RDA that comes with the kit is really lacking in flavor production. So if I order this mod, will that have anything to do with my flavor, or that’s all based on my rda? If it’s all...

Hey guys. So after much confusion on what wattage I should be vaping at with my builds, I have come across this technique. Now I know the math is different comparing mechs to regulated, so wanted to see if this makes sense to you guys. Basically what I’m doing to figure out what I’ll vape at...

so I’m finally getting the hang of everything...huge shout out to ALL OF YOU who have helped my OCD .... out. What I’m still confused about is...an 18650 charged to 4.2 volts. Now, depending how many watts I have my mod set to, and my build, sometimes when I vape the display on the screen...

Hey everyone. So for safety I am using a regulated mod, and I have some questions I hope you guys can help me with, because I’m tempted to just go back to my Smok stick for it’s sinplicity, but I really don’t want to, the flavor is weak, and I want that massive vapor. A few questions I have...

Hey everyone. My name is Joe from New Jersey. Excited to have found a forum, idk why I never thought of searching for one before. Anyway just wanted to reach out and introduce myself, not new to vaping but just recently getting into RDA’s so if anyone can point me in the right direction it...