Search results

It is almost exactly one year since my last post in this thread. For over a year Hussar Project X is the only RTA I use. All my other RTAs including doggies and dwarvs were not used even once. My two 4 ml extension are so worn out that today I ordered two more extension kits. I did not followed...

I think he meant KAEES Aladdin MTL RTA. ALADDIN MTL | KAEES®Vaping, KAEES For You!

I do not think you will break it... unless you will try access deck without securing X on mod or stand. One thing to remember is that to pull out top cup (to access filling hole)... or pulling tank off from deck... X must be screwed to mod or any stand... pulling tank from deck is close to...

Well, I need wire not a spool... usually I cut wire into 6" strips and place those strips in small plastic tubes... I have a couple spools that are not brittle but wire unwind so spools are useless for me anyway. I still think that $4.25 for hundred feet of kanthal is pretty good deal even if...

At the same place 100' of Kanthal wire cost just $4.25:thumb:

Use 2 flat head screwdrivers. Press o-ring into indentation with first screwdriver and keep it pressed and with second screwdriver keep pressing o-ring in small steps all around until whole o-ring will rest in this indentation. With thinner o-ring it is much easier than with fatter one.

Hussar Project X should give you pretty close RDA flavor.

Yes.:)

:shock:.....

I also think that your problem is not too tight wick in coil. More probably too much cotton in wells. But even that is unlikely... maybe it is somewhat contributing a little but I think main problem is too big/fat o-rings that rest outside yellow tank over wicking holes. Those holes are quite...

Exactly like my Fresia..... I loved it from the first draw and hated it after couple days...:D I spent couple weeks trying figure it out where is a problem and finally gave up:(

I do not know if it's only the best flavour RTA out there but I know it is best of dozen different RTAs I own.:) As a starter RTA it is easy to use as long as people know how to expose filling hole or getting to the deck...:eek: that part can be hard for some ;) There is another Todd's review...

#1912 and #3049:)

Probably he vapes less than 1 ml a day. :lol: I vape 8 - 10 ml a day and on second day of vaping I start to notice loss of flavor and difference in draw. I change wick and coil every other day... in the past I was cleaning my coils with dry burning but I noticed how much stuff was flying...

I also do not noticed any difference in flavor but I prefer regular single kanthal 26 gauge wire over clapton because I change coil and wick every other day and I am finding it easier to wrap coil and wicking it with single round wire. I never clean my coils as cleaning takes for me more time...

WOW!!! I can say only one thing... I agree with you 100% for every sentence you wrote in this post. :)

No, you do not have to get up to 30W to have good vape with 26 gauge. I never vape above 20 watts ( usually it is 14-18) and for me 26 gauge do not take too much time to heat... unless I will make coil that is longer than 8 wraps. How long time coil needs to heat up depend on mass of coil...

The first time I had jam I tried to get chimney off base but even with help of vice and other tools I was unsuccessful... I made plenty of scratches and was close to destroy X...I almost gave up... but I assembled back top section installed it on mod and... pulled it off easily the same way...

Yes that jamm happens when we place top section unevenly and make a twist to lock it. The best way to avoid such jam is to make firm pressure and small twist back and forth untill full twist is going easy. To get out of such jam instead trying to twist back we should pull it off with little...

Place (screw it)your X on mod. Close JFC. Hold your mod in one hand and grab the whole X with other hand and pull it off the same way as you are pulling top cap. It is necessary to use as much force (or more).