Search results

Hi all, I'm desperately looking around for a series mech mod as in the past 2 days, my HOG has packed in and my DotMod switchable series / parallel mod has decided it will now only work in parallel mode. I've been trying to scavenge through the UK ecig websites and I cannot find a series mech...

Steam did the biz. Thanks. Looks like the build I'm doing comes out at around 0.615ohms per coil. I built it on there as a dual core staggered clapton with ribbon wire as the outer.

It's a paraseries mech mod, which is why I have to get the resistance right. 2 cores, but each core is claptoned independently with 40AWG SS and then the two are held together with a 0.3x0.1 flat wire wrap. According to "Vaping Tool" a single strand of 32AWG claptoned with 40AWG (3mm ID...

Hi all, Can someone recommend a good free coil calculator? I'm working on a build that's a bit advanced and well past your normal twisted pair and I want to see where the resistance will end up once I put it all together. For reference, it's a SS316 build. 32AWG Inner, claptoned with 40AWG...

Juggernaught wire is about 2Ω/m? So 6 coils parallel, 3mm @ 11 wraps = about 0.07? Sounds tasty at 15 volts.

0.632Ω max build then. I think that works out to 25A @ 395watts. That would be fun to try.

I'm not sure I want to know how many volts.

Is that thing. A. A vape? B. An enforcer? C. A torture device? [Edited]

There should be lots of room, it's a 40mm deck. Had to go 10 wraps a coil though to get some ohms into the build. Might try your vertical coil build though.

I use cotton bacon Anna. Here's the build. IMO it's pretty ugly but I had horrendous trouble trying to position these braids so they were away from the cap without them either A. Springing straight back or B. Being massively pulled out of shape.

Gracias ladies and gentlemen. I take it all in the nature it is meant. Now let's get back to what the OP intended this thread to be.

Here's pics:

I accept the roasting and perhaps deserve it, but I already said I ONCE, during a misguided and dumb adventure vaped at 75amps and would have deserved everything coming to me. Never again. I shall now seek to have appropriate batteries for the task in hand as well. 30A required, 30A is what I...

Sounds fun, or bleeding expensive. I think I'll just buy some 20S's and vape at 29 amps on a 30A cell.

No, the vapergate mason is a straight-up 40mm RDA. I've never squonked. Looking at the bottom, all appears to be present and correct, though I note the 510 can be unscrewed with a flat-blade screwdriver.

Disturbing

I'll have to check it out. This happened before on a Nova style clone RDA, but now it's happening on my authentic Vapergate Mason as well.

Different build that was far harder to keep the ohms up. I have before been a complete idiot and vaped 700 on a dual batt series mod pulling 75 amps. Stupid and foolish times and I probably deserved to blow myself up. I have brought it down to about 29 amps now, but should go buy some Samsung...

Probably sounds worse if I say that I drive at 20 miles per hour over the limit when the road is empty too... Always really been a live-fast die young kind of person. Selfish, yes, but already been almost dead twice for no fault of my own anyway so may as well take destiny in my own hands. Are...

I like my vape to hit HARD, so perhaps my current setup is the best, though I'm probably cooking my lungs and the sensible out there will tell me that my vape is going to explode and take off my hand / face, but right now it's the HOG with 4 braided coils over 10 wraps putting out about 500...