Search results

138 grams dry. Used to be a gold plated dvarw but the plating sucks on these. Get a stainless one! Used to run a stock tank on a pico. Was HEAVY. Running the bell cap takes a lot of weight off and keeps the heat from coming up to the drip tip. But going to the plastic Tesla mod I found...

Leaks mean you don’t have enough wicking.

Vape mail! Weighed the pei tank at 4g, it is 13g lighter than the stock tank... that is almost half an ounce. Now the question is... will it break when I drop it? Time will tell...

I think I found the good hit. Lots of wick and coil close to the top. This one is 3.2mm ID and I don’t know how it doesn’t short lol

Tell me about throat hit. I can’t even get close to the th of the doggy. Same for both tanks: 2mm id spaced coils. Juice 53vg 4.3mg diluted to 47% with unflavored. Here’s what I’ve tried: All afc inserts (back to 1.2mm), 2mm is real nice as dL tho. Coil near afc hole Coil very far away from...

I made an excel spreadsheet just for stuff like this. I like to dilute my fav hulk tears juice down to 33 to 50 percent. Also mix my own flavors occasionally, but they don't usually turn out any good. Basically, you input the quantities and details, and then use a single digit for flavor. In...

unlock the resistance and see how much it changes when you hit the fire button. temp control measures the change in resistance of the coil as it heats to estimate coil temp. kanthal doesn't change enough for vape temps to be reliably used in TC. if you're at .17ohm, if the coil changes...

I sure hate firing delay. All my eleaf mods do it. But with af firmware they fire fast. Dang I remember those days of ego passthrus. All my vaping friends were jealous about the usb plug on my battery lol. I first vaped in 2012 with the ego/clearo but it never worked well enough for me to...

Lipos are your best bet. The problem with 18650s is how hard they sag when loaded. Check out hobbyking. Go by 1/4 of their continuous discharge rating (no multistars). Something like a 5ah 25c. Turnigy makes good cells. That thing is awesome. Shinyitis now kicking in. What parts are needed to...

Best combo/setup for you! specs plz Dvarw 22mm mtl 1.2mm, 26ga SST 6 wrap spaced 2mm ID. Pico 75w with arctic fox firmware. 60w preheat for .2s, 35w 400F 1.3s drags. Brushed black silver. Hits fast. 3500mah Sanyo 18650. Hulk tears ejuice diluted to 40% with 4.5mg nic at 70vg. What’s your...

Perfect setup. Arctic fox firmware pico, SST 26ga, preheat 60w .2s, 3500mah 18650. Dvarw tank is heavy. I used the tank for a bit with the metal tank piece replacing the pc tank. Well it does add some heft and I went back to the pc. Im going to order the pc bell tank to try and eliminate the...

At those settings it will never hit 360f so you might as well just use power mode. The point of tc is to have it bounce off the temp limiter throughout your drag. Think of the temp as a rev limiter for your engine that you can adjust, with the watts being how far the pedal goes down. If you...

The screws are M2x.4 x 3mm or just M2x3mm.

Different mods do TC differently. TCR value pretty much tells the mod how much the resistance changes for a degree of C. so, a higher TCR value will give you more power the longer you draw on it (because it expects a larger change in resistance), and a very low TCR will lower the power very...

welp, the 5 wrap 26ga sst coil did not work out. I tried it in many different settings but it just smokes the coil no matter how I set it up. And if it doesn't, then there isn't enough vapor and throat hit. I guess with higher VG juices you need more vapor for more throat hit. I swapped in my...

@Letitia about the arctic fox, I just installed it on my iPower 80w. It's better than stock. Took me about an hour to really get it dialed in. There is less fire button delay (with stock software I never measured the delay, but it was always so slow). I have setup three profiles, one MTL TC, one...

I’m thinking some kind of micro sprocket with the cone part and a smaller sprocket on the outside you push with your finger, or maybe a worm gear, lol I dunno. Maybe I’ll just get another set of jet drills lol! The thing that makes the biggest difference in consumption is the amount of surface...

It’s temp controlled. The only thing that changes is the surface area of the coil. The mod does everything else. I got the setup working on one SST coil, now I can build any SST and get the same vape pretty much. You know what would be cool, is adjustable airflow like on a carburetor jet. A...

Started with 1.2mm afc, too tight, now on 1.6mm too loose. Going to drill out the 1 and .8mm inserts. Can’t seem to find my jet drill set. Have only a .049 drill (1.25mm) that I’ll use to drill out the 1.2mm. Was vaping too much juice at 6 wrap 26g SST (.35o). Just went down to a 5 wrap 26g...

Assuming no mechanical defects (shorts), at typical MTL power levels and draw durations, even fake 18650s won’t be strained.