Search results

Just my winged list of $$ for mods, best and worst. Worst: Dovpo Topside (door design) Topside Lite (woeful board), Lost Vape Drone (510 fitting, leaks). Best: YIHI SX SL Class, Lost Vape Therion, Lost Vape Ursa Kit (Favorite). I use mesh RDA and RTA (Profile-Damn Vape) and prefer Aspire...

No replies?, My view and preferences are Kanthal or SS316. The Profie 1.5 will accept the wider mesh strip while original 1.0 takes only the narrow 16mm mesh and I also prefer the more open coarse mesh, the finer mesh seems to cake up faster but that can vary with the type of juice used. I tried...

I use both 1.0 and 1.5 and find that they both perform well. The 1.5 have a wider mesh clamp and can use the larger strips and also has improvemets to O-ring design. The original Profile top cap was a bit loose and the bottom base ring too firm. The 1.5 is my choice.

My favorite combo is a Profile 1.5 with a Dovpo Carbon Dual, love the YiHI board. The worst is the Dovpo Topside Lite which is really great but let down by a very poor board.

I have been using Grahams for over 18 months mostly on Profile RDA's and they are my primary setup. I use mainly tobacco juice and some dough and get about 2 weeks rotating 4 RDA's. My mesh will usually last 6-10 rewicks after a wet/dry brush clean. I use the bowtie wick cut Vaping with Vic on...

Been a while, I planned to a post your favorite Squonk kit and found this thread. Have a fair few Squonkers mostly with a Profile on top, but my go to is a Topside Carbon. #2 is a Topside Dual. I also run a VV V2 and Aegis. My most hated is a Drone with the defective 510 feed system and akward...

I often go to the local park on my scooter, eat a apple and vape a tad...I always notice a deeper flavor profile outdoors and wonder why? If anyone is really bored and needs a challenge....update your Windows computer, this will keep you occupied for days. Not recommended for high blood...

I have a Pulse 90 and yes I do get some leaking but mainly around the 510 atty fitting. All my Vandy Vape mods tend to leak at the 510. Make sure the silicon tube extending from the bottle fully covers the the metal nipple inside....I always give the tube a slight pull before replacing the...

If you enjoy mesh coils then the Profile RDA is tops,. The Profile RTA is great but need's careful wicking, the Damnvape Doom is also good. The Recure and Beserker are the only coil wound atty's that I still use.

I have just discovered the world of Mobility Scooters, with my eyes fading due to MD I decided money spent on insurance and rego was a waste. I sold the car and got a Harley-Like 3 wheel scooter...but I also noticed that vaping outdoors adds a whole new flavor to my vape...also after eating...

Still messing with my Intense RDA's. I have found that wicking is a tad fussy. I use rayon rope and started by using a single length, soon discovered that more is better and now do a double fold...u the ends and feed the bend under the mesh, this gives a stronger flavor hit. The single width did...

Duh...Australian ban now delayed to January for parliament debate, political hip shooting for PR.....so what's new in the Nanny State. Public out cry has made the Health Minister back down, the side benefit was that New Zealand, the main Aussie source for nic saw a huge increase in orders for a...

Been a while now and so far no new users have made any comments, I guess delivery of the Intense has been delayed. My original comments still hold, the flavor is muted slightly although not really bad. I have 3 units in constant rotation...just can't seem to let them go. The good side is that...

Interesting the restive nature of our coils and regulated devices and associated circuitry. My mesh setups at times exhibit a lack of consistency over time and I have wondered if this may be due to a gradual contact degradation. The mesh coils mostly use clamps and flat surface contact by...

Much the same here, the Unity has been a challenge, I have set the Unity aside 4 times but keep trying...currently I use only cotton and set up using vaping Vic.s method, careful not to pack the wells and keep a heavy shoulder bowtie style, so far good. My other mesh conundrum has been the...

Same here...6 weeks and counting, shipped but no transport.

Punk said it all...I have found that the mesh RTA a more constant setup, noticeably the VV kyln M. I also prefer to use power mode over TC (love pulse mode) as TC mode tends to fade as the coil gunks up, call me lazy.

The China factories I believe are mostly closed, I mistakenly ordered 3 ...2 x SS and 1 gunmetal just before the outbreak and were here in 3 wks maybe I have a collectors set. Here in Australia I have not seen any on sale yet....could be a long wait.

I understand the problem, it's the free ends, lack of a continuous border. I always dry hit, low watts with no wick prior to wicking, if you see a bright flare then a dry hit is assured. The current virus problems in China have shut many factories so supply is halted. You may find that the finer...

The mesh can be cut from any type of vaping mesh including, Digiflavor, Vandy Vape strips which come on rolls. The OFRF mesh is 16 x 6.8 and the Intense is 16 x 3.5 both SS316L or Kanthal will work fine. I get my mesh from Aliexpress (China) see link. Buy Products Online from China Wholesalers...