Search results

It is amost the end, what are you looking to happen and what are you going to do to keep the battery charged...:)

Looking to maybe get one of these, but are these metal bodies? Seen some at different sites that are plastic and would most likely not last as lone as metal ones.

Was thinking of getting a Kgo the next time I needed a new battrey. On some of the sites that sell Kgo's they have a waning that they can not use a ego charger. WHY not? The site also sells seperate chargers for Kgo's, but do not say any thing about not using them on Ego's. Are the chargers...

In using the quick reply entry the spell checker button does't do anything,xccv, doesn't do anything on this text entry eirhter:mad:

Not much info, but it is on their main page and is fairly positive. The good thing is that more people will see that the e-cig is getting more main stream.

Was looking to get some menthol crystals, none of the vendors I use do not carry the crystals. Was looking for something on amazon and noticed that they have several different sizes and several sellers of menthol crystals. Since I do order stuff from amazon, I was wondering if the crystals they...

I need to get some menthol crystals and saw that Amazon has some listed. Are they the same as those used in ecig juices? Are there some that are better others or some to stay away from?

Some where I saw someone was using the grunge off product to clean some of their equipment, but I can't seem to find the post again-(forget the search, comes up with too many hits). From what I can find on Amazon the stuff is suppose to be used in pipes for cleaning off the burnt on tobacco...

Just checking to see if you are going to run any labor day specials, need one that covers small 10ml bottles as I need to check some new flavors:tongue:

Just had to dump one of my newsapphires, the juice was starting to get that burn taste, took it apart. Appears to be really well made, but would take a little micro work to put it back together(old eyes). After looking at it awhile I thought what would make it real nice if the atty part of it...

What do I need to know to clean the sapphire? I am thinking it would be something like CE2 - wiggle the plastic tube off, use water on the parts - how do you reach/take apart the atty? Then put everything back together. Looking for any special points that may cause problems and don't do that...

I have the infinity and was using the batteries that came with it. One of the batteries went dead and I bought some new ones and they didn't seem to operate the infinity. The new ones I got are the ultrafire 14430's. After looking at them for awhile trying to figure out why they didn't work, I...

eGo passthrough(PIPER-D) - Detailed info for eGo passthrough(PIPER-D),eGo passthrough,eGo passthrough(PIPER-D),PIPER-D on Alibaba.com Found this pass through while looking at the alibaba site and I would like to get one - I don't need 100 of them. Main thing they look nice and are VV, just what...

Just got my epower yesterday, used it till button started flashing, put the battery into the changer. Removed from plug last nite - after 1 1/2 hours still red charging. Pluged back in this morning to finish charging it - after about an hour the charger led started flashing real fast, did not...

Been thinking of getting a e-power for my next e-cig, but I'm not seeing any good/bad/ugly about this setup. Is it being covered in some threads somewhere else?

My store bought pass thru quit working and I have another one that broke. So I thought I could try to repair the broken on. Basically it is a usb cord into a plastic holder, but the board inside was broken and some of the wire was unhooked from the solder joints. What I'm thinking of doing is...

Just got 2 boxes of the clear green flexomizers, all the other clearomizers I gotten over the pas few months have been clear, the green ones look real nice. Out of the 10, 2 already had some small cracks at the bottom, but I always tape wrap them using clear shipping tape to keep them from...

Just had a problem with one of the vortex when I was filling it. Half filled it and put the cap back on to do something else. When I took the cap off to put in more juice in, some bubbles came up from around the side and a bunch of juice came out the center hole. Looked for some cracks, couldn't...

Just got my order from GotVapes of the Vortex clear cartomizer. Seems to be a fairly good vapor producer. Also the plastic tube seems to be thicker than that used for the clear ce2's. If they continue to work a good as the first one I tried, I maybe replacing my clear ce2 with the Vortes. The...

Was looking at some of the mods and parts, but could not find anywhere instructions on building the mods. Was looking at the vv and using a regular box to put it in, but don't know what parts I would need to connect the two and what type of batteries I would need. Looked around the site and...