Hubby vapes at much higher watts than me and has had similar issues. The only fix I found was packing some cotton under the coil to help increase wicking and keep the coil from sucking up all the juice around the coil so fast.
Sent from my iPhone using Tapatalk
Been a long time since I've been on ecf so saying hi. I've refered a lot of people here though. Seems most of my old favorite forums are dead. I started vaping in 2010 and joined ecf before I got my first kit in the mail. I've come back because this deeming reg is so confusing and imo over...
I was handed an itaste vv to see if hubby can fix it. there is a disconnected grey wire at the top that I assume goes on the board. but there are no leads anywhere to go to the p/n on the 510 connector. anyone have any pics for the connections from the top board to the connector or links to pics?
I would like to try to make my first mod. I am looking to make a 3-6+ volt mod with volt and if possible ohm display I plan to do 2 18650 in series or 4 with 2 series paralleled( if I'm saying that correctly). I have never dealt with boards and resisters before so this is completely new to me...
Have you checked to see where tracking shows them at? Try http://www.quantiumaspac.com/qtracker/track.aspx
I would not expect the one shipped on 12/17 to be in the us yet and they may have actually been shipped or picked up a few days after ft marked them as shipped.
How slow has customs been?
I had a package mid dec hit the us and clear customs the fallowing day and i got it 3 days later. I've also ordered from us venders from One coast to another to me in ok and got them all in 3-4 days.
I have 2 packages that only show they have made it to the us. No...
I had 3 DIY mixes i had just a bit left in each bottle and mixed them together. Surprisingly it tastes great.
Mocha , peppermint patty, and desert ship.
I don't think the new head works on other pt t3 or evod tanks but plan to check that myself as well. Also plan to see if heads interchange with the aspire which from pics look the same.
I just realized i have 5 packages in the mail
Fast tech- jm clone and Helios clone
Fastech- kraken
Nic, vg and pg
Protank 3 and ss mesh cartos
Solder epoxy ( to fix a mod that recently broke)
Evod heads can be used in protank but protank heads can't be used in evods. Or so they say. I have used the protank heads in evods and t3s but the bottom cap doesn't screw on tightly. It leaves a little gap. But they never leaked on me.
With good care and cleaning and even an occasional rewicking a coil can last several weeks to over a year. I clean mine Mostly every 2-3 days or every flavor change with PGA and then a dry burn. I do this with clearos and rdas. I have one rda i use cotton in and I just remove cotton, dry burn...
The high volts can definitely cause issues too if you have it set all the way up. First make sure its well primed. On volts/watts its good to start low and work you way up. Especially on a new carto/clearo ect. I normally like 8w but even a new carto I start back low and work up slowly through...
Welcome back. I too recently returned after being gone a while. Things have changed a lot in that time. I'm just now getting caught up on whats new and building my wish list.
Have you tried priming by taking some dry pulls on it? Drip priming will leave dry spots even though you think its full.
I will drip then roll it between my hands. Redrip and repeat till it comes out the holes then once in the tank do some dry pulls and even more juice gets in. When I do this...
After us they will be going hard after the fatties and caffeine addicts and who knows who else that they want to control for the sake of the children or some person whom its of no concern to. Seriously if my kid gets fat its my fault not McDonalds or 7-11 for selling big gulps. I coulda bough...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.