Search results

  1. iuseaspork

    need help finding a reliable rebuildable

    I use pretty thin juice. Mostly 80% pg. The last few purchases have not been great for me... Fogger, rocket... I need something that just works. After the rocket, I'm scared to death of kayfun type things. Anywho, I want advice from someone that uses thin juice on what to get next...
  2. iuseaspork

    This is my favorite build on my rsst thus far

    It is simply two 32 gauge wires run parallel around the wick and separated to even out the heat. What it works out to is about the resistance of a twisted coil at 4 wraps, but the contact area of a single wire wrapped 8 times. Here is a terrible pic that you won't be able to make out a thing...
  3. iuseaspork

    My "carto-tankanoid"

    I love my rsst and my evods, but I wanted something new. This thing vapes great and is super easy to fill. Probably won't do a how-to, but the parts came from a ce2, ce3? (Bottom coil), and a carto tank. The ce3 tubes have to be forced into the tank probably destroying the o-rings. Rebuilds...
  4. iuseaspork

    i believe i have a plan forming

    Boosted feeder. Might have enough room for on-board charging.
  5. iuseaspork

    Here is a bottom button mod I banged out today pretty easy.

    It's tensioned with ball bearings through holes in the side of the tube and wrapped in shrink tubing. It's a nice and simple 14500 mod. I already have a lock (so it won't accidentally fire) designed for the bottom, but ran out of time today. Oh, and the center pin is adjustable:cool:
  6. iuseaspork

    Why does the average voltage on a scope not match the set voltage on a PWM mod:

    I've seen this mentioned a lot in reviews, so here is why: In a traditional mod lets say we set the voltage to 4 volts on a 3 ohm load. These are the results from OHM's law: Current: 1.33333 Power: 5.33333 Now lets double the voltage to 8 volts: Current: 2.66667 Power: 21.33333 You can see...
  7. iuseaspork

    An interesting experiment

    So I took apart an old Dual coil and made a wick hole through the sides. I then made up a ss coil and pushed it in through the bottom so it stuck out the holes on the sides just a little. I wrapped it in gauze and put it in a tank. So I ended up with Throat hit that could kill me without...
  8. iuseaspork

    2 orders with a great experience!

    I've not run into a vendor that didn't offer me a good experience yet, but I really feel that this guy has it together. I did have a problem on my second order that was taken care of swiftly. The extra step of the ordering process really doesn't bother me and the prices are great on most...
  9. iuseaspork

    My new variable tube length mosfet tube.

    Just finished it today with a 50mm battery tube. Thinking about painting it, but I suck at painting. Plenty of room for the mosfet and switch beside the 510 connector for a smallish mod.
  10. iuseaspork

    I think I've made my first successful genesis!:

    After being inspired by this thread, I think I have something I can use. I basically took a different approach to the soldering by coating all parts with flux and using lead free solder. I had a lot of failure (I didn't know that I could braze the brass to my galvanized bolts.), but that's...
  11. iuseaspork

    You know you belong in this sub-forum when...

    Your dremel takes a half inch bite out of your finger and you go right back to what you were doing after it's bandaged up. ...This damn thing better be worth it!
  12. iuseaspork

    Stardust cracked tube fix: 1/2" ID vinyl

    Stardust cracked tube fix: 1/2" ID vinyl ...Just cut about an inch, lube it up with juice, and slide it on. It goes on very tight.
  13. iuseaspork

    Home made soldering flux!

    OK... You guys are going to think I'm trolling you, but I read this somewhere and had to try it. First I will tell you my results and then tell you how I made it. I had a small piece of CE2 center tube laying around. These are hard to solder to with just rosin core. It can be done, but it's...
  14. iuseaspork

    Just had to brag in a more visible spot. (PWM VV Box mod)

    http://www.e-cigarette-forum.com/forum/battery-mods/194095-my-first-pulse-width-modulator-mod-35.html#post5516412
  15. iuseaspork

    Same recipe... Mostly PG - good ...Mostly VG - BAD

    OK... Same ratio of flavoring (2-3% tobacco) I am using 4 drops of vinegar to 10ml of juice. 90% PG the flavor is almost too much! 90% VG the flavor is not even there at all. Actually, it's almost bad!? I'm using Wilton brand VG. Do VG recipes need to steep longer? Do I need to up the...
  16. iuseaspork

    VG with dual coil cartos in a tank

    Any special considerations for 100% VG? Does it even work?
  17. iuseaspork

    Resistance goes down as I take a couple of hits

    Here is a link to my atty. OK... Make a new coil wire. 2.6 ohms. Wind my coil and get all set up. 2.5 ohms Take 2-3 hits and notice the vapor is hot and burnt. Measure... 1.? ohms! Mess with coil, measure... 2.5 ohms Take a couple hits and back to 1.? ohms Done it 3 times now. WTH is...
  18. iuseaspork

    The start of a new atty with inspiration from many

    I hope this works out.... Teaser pic: Consists of 20ml syringe parts, old carto case that will be slotted, a pretty big needle (will need another... I broke the rest trying to bend them), and a silicone cap from a fluxo (CE2). The wick that is sticking out is for inspiration. the real wick...
  19. iuseaspork

    Wizard labs

    Wizard Labs Ordered a bunch of tobacco flavors from them. They threw in a few freebies (although with their pricing I would still be pleased if they hadn't). Shipping price and speed was good. Packaging was almost excessive. I couldn't wait to get to the goods buried deep in layers of bubble...
  20. iuseaspork

    Looking for someone's proven recipe using these flavors (tobacco)

    ... or a good place to start All from wizard labs Concentrated Commercial Tobacco flavoring by Seedman Concentrated M-type flavoring by The Flavor Apprentice. Concentrated DK Tobacco flavoring by The Flavor Apprentice. they call it 555 Concentrated RY4 type flavoring by The Flavor Apprentice...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu