Search results

I was thinking that I was getting constant irritation and tightness in my lungs once I upped my wattage also. I went back to old school since I have boxes of boges cartos laying around. Mixed up some high pg ejuice, added it to a phinia tank and I'm back to chain vaping without any adverse side...

Glad I'm getting feedback about accumulating phlegm from vaping VG. After I switched to heavier VG use I starting getting congested . I have been vaping for over 4 years. No problems whatsoever. Once I switched to sub ohming and upping my VG mix to 60vg/40pg then to 80vg/20pg sub ohming, that is...

I just purchased over a MadVapes an Smok Omnitester. It reads ohm resistance, voltage drop on mods, ego batteries, pulse modulation vv mods, etc.... compared it to my vamo reading ohms for a dual coil build. The Omintester instantly read .2. My vamo read .4. Boy I was ....... Didn't know which...

Put my nemesis to rest and now loving the Panzer w/ helious clones. 28 gauge wire dual micro coils w/ organic cotton. Hella vaperlious pulls.

Ace of Vapes fixed my vamo. $10.00 2.90 to ship to them 2.90 to ship back. I asked if they can replace dna 20 battery packs if I cannot solder them in without destroying the box.

I wonder why after having mine for just a few weeks, it no longer makes contact. No reading on my meter or other reading devices. What can go wrong with it to do this. I completely tighten down my coils and test them but no go. What can I do? Help.

Started at 24mg with the commercial silica wick tanks and atties. Went down to 18mg and found myself vaping too much to get satisfied. Once I became a dedicated dripper and learned all about rebuilding my own coils for lower ohms down to sub ohms I had to cut the nic level in half. Same went for...

I had my tank set up on a mod slid into my side mesh pocket of my back pack. The tank was sticking out of the top of the see thru pocket. No one bother to ask what it was. Once I got thru the inspection I took it out and started vaping. This was domestic going to L. Vegas. Don't know about...

I have almost giving up using ss mesh but using a good torch made all the difference in the world. I torch mine thoroughly many times over and then juice it a few times and let it burn down holding or bracing in an upright position. I torch and ejuice the wire too. It all helps build oxidation...

For the real AW batteries, buy from AW. You should go through CPF market place, Fresh authorized AW batteries. AW's LiIon Batteries Sales Thread *Part 12*

I have the grey Panasonics,Efests, and AWs. My old AWs seem to deliver more power output than my new Panasonics or Efest. There is a noticeable difference. Not talking about battery life. My coils heat up faster and hotter. I'm going to stick with AW's and try out the MNKE's next for low ohm coils.

You must a knock off vivi nova. I have the orginal that has the raised knurling on the rims at the top and bottom caps. The center post is shorter than a smoketech and some of the other knock off mini vivi nova's.

If you keep your evic on others said that it has drained the battery. On another forum, Joytech responded to this issue saying, "Thank you for your information. We will add this function in the following version: when the voltage of battery is low, it will automatically enter the standby mode...

Yes, I have been using my evic every other day between other mods I use.I never turned my evic off. For some reason it will not turn on. No LED showing. I slipped the usb plug in and the led lights up showing that it charges, but it will not power up anymore. I tried new batteries so this isn't...

Once I punch my hole I add my ejuice and do not add any in the carto from the top. It keep the intergrity of the filler. If you add more juice to the carto plus the ejuice pulling in from the hole, it will flood and collapse the filler from being flooded. Mine works for at least a month with no...

I have the revised Vamo with the longer spring cap that lets you use flat top 18650's. I'm loving it! Its not build like a cheap China plastic or aluminum tub mod. It's built very sturdy. It's heavy and has a nice feel in hand. It blows away my lava tube.

I got mine from Zainy on VaperHawk for $36 free shipping. It just arrived. Delivered in 2 1/2 weeks Ainy now raised it to $38 free shipping. It would have cost $39 plus $8.20 shipping, total: $47.20 on her .net retail site. It really feels like a quality product. Strong and sturdy...

I just received a Vamo with black buttons. Waiting on one in Blk Chrome in one of our c0-0ps. This one feels very sturdy & has a decent amount of weight to it. It seems to be working very well. We'll see how well it holds up in the near future.

When I first started making ss mesh wick coils, I was a mess. Hot spots, shorts, etc.. I saw the Petar K vid and found everything was so easy to make a perfect coil first. Checked it to see if it is glowing bright orange red, then slip the oxidized mesh in place. A no brainer. Just to make sure...

I totally agree! My shelf of e-cig acessories turned into shelves, and now into a cabinet organizer with sliding drawers. Ahh but its soo much fun!! :)