Search results

  1. dirtyrigger

    Cloupor T6 & T8 Firmware Update

    EDIT; the update was successful. There are a couple new personalization features now that could appeal to some people. The power output I think still needs some work, but I've done only brief testing. I plan to put it through the gauntlet so to speak this weekend and gather my data into a couple...
  2. dirtyrigger

    Cloupor T6 & T8 Firmware Update

    That's funny, I sent a similar email on 12/24/14 and they offered to send me the beta update to test it out. the cloupor rep who has been in contact with me had trouble attaching it in an e-mail but I just downloaded the update file on Skype, I'm still waiting for her to get back to me about...
  3. dirtyrigger

    nichrome 80 wicking issues

    Hey everybody I've been using organic cotton (the balls from Walgreen) and kanthal for over a year now and before that I was exclusively on SS genisis builds with kanthal. I just got some 24g nichrome 80 the other day and I really like it when it is freshly dripped but I find that I'm getting...
  4. dirtyrigger

    Nemesis clone - some questions

    Just got my Nemesis today and I'm loving the switch. It was crunchy at first but I disassembled the switch and used a pencil to scribble all over the shaft that slides through the brass ring. the graphite acts as dry lube and makes it easier for the parts slide without binding. Six hours after...
  5. dirtyrigger

    KTS / With Kicked NCR18650B

    A kick defeats the point of a mech, imho, but either way i don't believe a kick can handle the amount of current that runs through a sub ohm circuit. a 2 cents for safety fuse might be able to handle it but I'm not sure what its amp limit is. use quality IMR batteries and a healthy respect for...
  6. dirtyrigger

    Berry & Melon DIY RECIPES

    Tpa Honeydew With A Little Blueberry Extra Is Superb. Don'tKnow Why My Phone Is Capitalizing Everything
  7. dirtyrigger

    Ok, trying to buy unflavored Nic juice to DIY...is the FDA Apocolypse wiping everything out or am I looking in the wrong place??

    i ordered some nic from rts vapes toaday. i dont know but it seems that 48mg is the least expensive strength in their inventory if you go by $/mg. it didnt make sense to me, but you save $1 buying 250ml of 48mg vs 100ml of 100mg and they both equal 12000mg of nic.
  8. dirtyrigger

    Aga - T2 & Vamo

    There's no special method, just as long as the hardware isn't loose and the lead is trapped
  9. dirtyrigger

    Ac9 fit issues

    have you tried backing out the positive? raising the positive post should allow you to screw the ac-9 down further.
  10. dirtyrigger

    Aga - T2 & Vamo

    that sounds reasonable, but if the aga is the only device having this problem on his vamo then i think the issue would more likely be the aga and how it is contacting the mod... not enough info was provided to rule one way or the other. also, getting a resistance reading of 4 ohms on the...
  11. dirtyrigger

    Aga - T2 & Vamo

    i wouldn't pull at the post on the VAMO. just loosen up the nuts on the aga center post and push the post lower than it would ever have to be, then screw the aga on the vamo, the vamo will push the center pin up, but not too far up, run the nuts back down and you can rule out bad connection...
  12. dirtyrigger

    Low Ω 28g vs twisted 32

    my experience is the exact opposite, i find twisted 32g coils last longer with less maintenance. They both vape about the same though at equal resistance.
  13. dirtyrigger

    I might have figured out Tribeca

    I use that recipe minus the cappuccino. Its pretty dead on. A friend of mine who buys tribeca regularly took a rip off my pv then asked if i stopped doing diy or if i just got the one bottle cause i missed that flavor... he wants to get into diy now.
  14. dirtyrigger

    Unoxidized SS Mesh Build for Gennys

    With the "unoxidized" setup you are oxidizing the wick with the coil, that's what the pulsing is accomplishing, so it doesn't mater if the wick is grounded because you have a carbon layer between the wick and coil.
  15. dirtyrigger

    RBA and VV Devices

    They work fine on vv devices, and if you're new to rba i would recommend using one because of the built in short circuit protection. After you get some experience with them though you will probably want a mechanical mod so you can push the envelope looking for that"perfect vape".
  16. dirtyrigger

    PG causes DWI's???

    About seven years ago i had to have an ignition interlock device on my car because of some bad decisions, i had to prove to it that i was sober before my car would start and it would test me randomly while i was driving. I had to pull over on the side if the road one time because i had some...
  17. dirtyrigger

    So this non-oxidized mesh thing...

    Thanks to this thread I've been enjoying un oxidized wicks for almost 2 weeks. The first one didn't take a half hour, but there was a time where the pulsing didn't seem to be working. i adjusted tension on the top coil and that was all it took, just twisted the 2 nuts that capture the positive...
  18. dirtyrigger

    First mechanical mod?

    Don't hate what you don't understand. If you're looking for vapor you should stay away from my .6 ohm coil cause i can't $#*t when i exhale.
  19. dirtyrigger

    Unobtainium, Chinese clones, out of stock, how do I score a quality APV

    Vape dudes has the electric angel and i think they are in stock, check out the pbusardo review i can't remember how he classified the quality of the device.
  20. dirtyrigger

    Cheaper, But just how much cheaper ???

    I had a friend ask me this today so i sat down and figured it out. About $1.61/30ml comes to about $0.05/ml. I will probably bring this down since I've finally got about 4 or 5 all day vapes now so i plan on buying in bulk so i can just mix up a couple months of juice and experiment less. Even...