◙ Li’l PINCH (←thang) ◙ pdib (←maker) ◙ not sayin’ (←just sayin’) ◙ shuh-ZAM! (←hyperbole)

[damselle]

Bee will have to hand deliver pinches from now forth, just to be safe

Sent from my GT-I9506 using Tapatalk

Shipping costs would be steep, but might be worth it to squeeze Peters cheeks

 

[muzichead]

gosh . . . y'know, looking at those pics of the Little Ory . . . I could almost see someone making a pseudo chuff tip that friction fits around the delrin insert, down over the first two ribs of the cap, and sits on the rim of the atty cap there. . .. . hmmmmmmm . . . interesting.

. . .lemme take a couple measurements here . . .. . fat 1/2" ID . . . 5/8" OD . .. . so 1/16" wall thickness. . . ..

oh, well . . .. just an idle observation.

I'll take 2 for my O-16's....pleeeeeeaaaaase....

 

[Rossum]

Mrs. Bee's birthday's comin' up here. I've got her present all set up.

NOOOoooooo, it's not the mod, it's the topper!
(heck, I don't love her that much)

seriously tho, the mod is just, well y'all know the story there; so, if she likes the mod, she can keep it. I got her an O-16 tho, because she's still stuck on the RM2 thing: stock air hole (in in this here year, 2016 . . . . ) . .. 1.2mm air hole and a single coil in a small chamber atty.

Anyway, I've been wanting to upgrade the quality of her vape without changing the dynamics, and the O-16 seems to be the one that'll do that.

Hope she likes stickin' her finger in the brother-from-the-same-bee-father-as-a-Doffy-Hole hole.

2mm Z-coil, in the middle, with air coming from both sides, like this:

Trust me -- I'm a tootle puffer too.

 

[Rossum]

Oh, and get her a smaller diameter DT!

 

[Doffy]

2mm Z-coil, in the middle, with air coming from both sides, like this:

Trust me -- I'm a tootle puffer too.

Am I the only one that read that in mark hamill's voice?

Sent from my GT-I9506 using Tapatalk

 

[classwife]

Oh, and get her a smaller diameter DT!

My thoughts too


Unless she likes

never mind...no good way to discuss

 

[B2L]

My thoughts too


Unless she likes

never mind...no good way to discuss

Ooooo... look, a quarter

 

[classwife]

Ooooo... look, a quarter

Yup

 

[pdib]

My thoughts too


Unless she likes

never mind...no good way to discuss

Classie . . . .

yer a treat!

 

[pdib]

So, thanks for the suggestions, Rossum. I figure she'll end up putting her fave driptip in there (thanks to keepsmiling); but she's using it. So, I just had the intermediary gizmo in there so I could check the vape on the build I did for her (compare it to when I build her RM2 and test the RM2 with her DT out of my way). And then I left it on there, for now, cause, . . . . it's a good storage place for it.

I really wanted to try a Z-coil and go with dual air holes; but she literally can't abide by any more than a SINGLE 1.2mm airhole. So, can't double it.

 

[pdib]

I'll take 2 for my O-16's....pleeeeeeaaaaase....

yes?

and, sooooooo . .. . ?

 

[keithu2]

So, thanks for the suggestions, Rossum. I figure she'll end up putting her fave driptip in there (thanks to keepsmiling); but she's using it. So, I just had the intermediary gizmo in there so I could check the vape on the build I did for her (compare it to when I build her RM2 and test the RM2 with her DT out of my way). And then I left it on there, for now, cause, . . . . it's a good storage place for it.

I really wanted to try a Z-coil and go with dual air holes; but she literally can't abide by any more than a SINGLE 1.2mm airhole. So, can't double it.

Z-coil with the two smallest air holes worth a try?


cuz' I really, really want her to like the pinch . . . . . .

 

[Rossum]

Z-coil with the two smallest air holes worth a try?

That's how I roll.

But I was all the way up to a 1.5mm hole in my Cyclones with a single coil and almost a full circle showing on each of the two slots on my Nuppins with duals.

Yes, yes, I know that's not the "in" way to vape.

Too bad.

 

[classwife]

Classie . . . .

yer a treat!

ok...I'll go away

 

[MamaTried]

ok...I'll go away

nope...

 

[Rossum]

ok...I'll go away

 

[e30ernest]

 

[keithu2]

That's how I roll.

But I was all the way up to a 1.5mm hole in my Cyclones with a single coil and almost a full circle showing on each of the two slots on my Nuppins with duals.

Yes, yes, I know that's not the "in" way to vape.

Too bad.

I'm right there with you. Main reason why I went with dual air atty's was all the dental work I had done - they don't want you sucking too hard on anything. Still running a rm2 @ 1/16", nuppins @ little over a circle, and the stumpy's @ 1 hole because I'm too lazy to redo everything and I don't know what procedure my dentist is going to try on me next.

 

[Doffy]

I usually run derringers with duals. But with how many mods I have now, I have set up my OG dibi with a vortice, single tootle twisted coil and one side afc. It is kinda nice

Sent from my GT-I9506 using Tapatalk

 

[Slots]

But I was all the way up to a 1.5mm hole in my Cyclones with a single coil and almost a full circle showing on each of the two slots on my Nuppins with duals. Too bad.

I'm with ya Rossum.
I run with single coils ... haven't found any of the duels I've tried to be any better than my singles.
I drilled my Cyclone out with a 1/16 .. much better
On the Nuppin, I have about 1/2 circle on each side.
I'm still playing with it, because my Nuppins whistle at me
Weird, they didn't do that before
I just don't care for an airy vape. My old Protanks are just about right.
Yup, I still use them on my Provari's and Vamo's ... good stuff doesn't leave the house.