Anyone try these yet? Saw them at madvapes. Look very interesting although it seems they are not for Ego-s. Think I'm going to order some.
510 "Dual Coil" Carto
- Thread starter C-kool Dad '09
- Start date
- th_trl_thread_readers 0
- Status
I just saw them on another site. Don't know anything about them, but they look interesting.
Please be sure to report back if they are worth my time....and what they do!
Please be sure to report back if they are worth my time....and what they do!
I got a newsletter from a different company that offers these. This company included this disclaimer:
"........Please note that these are not sutiable for eGo, 510, 901 or mosfet driven type batteries. These are meant to be used with 3.7 volt mods with a switch capable of handling 2 or more amps. Simple testing shows that although these are low resistance, they work wonderfully on 5 and 6 volt devices. Your results may vary and the protection circuits on some batteries at higher voltages may see these as a short and not work".
I don't know if MV has the same, but thought I'd just share what I read......
"........Please note that these are not sutiable for eGo, 510, 901 or mosfet driven type batteries. These are meant to be used with 3.7 volt mods with a switch capable of handling 2 or more amps. Simple testing shows that although these are low resistance, they work wonderfully on 5 and 6 volt devices. Your results may vary and the protection circuits on some batteries at higher voltages may see these as a short and not work".
I don't know if MV has the same, but thought I'd just share what I read......
I've got some, they didn't seem to hurt my batts. I'm sure they'll shorten the overall lifespan, but any LR atty will do the same.
For some reason Madvapes puts that disclaimer on just about everything.
For some reason Madvapes puts that disclaimer on just about everything.
I have used them an ordered more..... honestly I didn't notice a whole lot of diff in TH or vapor but I have been using ce2s. I thought the flav was better than in any other fillered carto I have used
ok, C-kool, where's the review??
Have I mentioned how impressed I am that you ventured out? WTG!!
Have I mentioned how impressed I am that you ventured out? WTG!!
I was AFRAID someone would ask that. The 'concept' is interesting, but my 'results' less so. I have been using them on HiVolt only (results could be different at 3.7). !st off - can't seem to get the God-Awful taste (primer?) out of these. I'm getting the 'flavor' of the filler material more than the juice most of the time (and I'm dripping with a tip to boot). They can get quite warm (hot). My original idea was for these larger size cartos to last longer before refilling - but it doesn't seem to matter so much, much like the ordinary (smaller) cartos.ok, C-kool, where's the review??
Have I mentioned how impressed I am that you ventured out? WTG!!
They work great on a mod, but I did fry an Ego battery using them. It was an old battery near the end of it's lifespan with a half broken button so YMMV. I'm loving them so far. I'm using them at 6 volts on a Maxi Roughstack V2.
The only time I can stand the CE2s are in Tanks. Otherwise I'm just hating the number of cracks, pocket accidents, etc. I get with the CE2s. So for regular cartos I stick to Boge 510s. I had a few SMOKtech dualies and I ~hated~ them w/ my regular juices. Yeah, tons of vapor but total loss of taste for me. I'm going to try Stormy's Tank based on the SMOKtech dualies and remain hopeful. -Magnus
Can you elaborate on this? My CE2's are steel and I have had no accidents or cracks. But if there are potential problems in the forecast, I'd like to be aware of them. Forewarned is forearmed.
I got a box from Cigtechs and they just arrived this afternoon.
Totally initial, first impressions:
Holy cow! Got over 35 drops in the thing! OK...but with 2 heating coils, will that cause me to go through juice faster? Hmmmm....
These are very low oHms. Like, 1.2 oHms low. Keeps freaking out the ProVari. I had it set at 3.7 volts to start and kept getting the E2 error, so I have had to keep lowering it. It's now set at 3.3 volts to try and keep the error away.
As advertised, the filler seems to be very fast absorbing. That's cool.
Draw - The closest thing to a regular atty I have had with a carto yet. Still different, but I don't get the airy feeling I normally get with cartos.
IF this throat hit/feeling continues, I could see using it full time on the ProVari. Kind of defeats the purpose of having a varivolt unit if I'm stuck at 3.3 volts, but it's not like these are my only cartos/attys LOL.
On a side note: I ordered the eGo T adapter for the ProVari over the weekend, but it hasn't been shipped yet. Can't wait to see how that hits on something with more volts than an eGo.
Totally initial, first impressions:
Holy cow! Got over 35 drops in the thing! OK...but with 2 heating coils, will that cause me to go through juice faster? Hmmmm....
These are very low oHms. Like, 1.2 oHms low. Keeps freaking out the ProVari. I had it set at 3.7 volts to start and kept getting the E2 error, so I have had to keep lowering it. It's now set at 3.3 volts to try and keep the error away.
As advertised, the filler seems to be very fast absorbing. That's cool.
Draw - The closest thing to a regular atty I have had with a carto yet. Still different, but I don't get the airy feeling I normally get with cartos.
IF this throat hit/feeling continues, I could see using it full time on the ProVari. Kind of defeats the purpose of having a varivolt unit if I'm stuck at 3.3 volts, but it's not like these are my only cartos/attys LOL.
On a side note: I ordered the eGo T adapter for the ProVari over the weekend, but it hasn't been shipped yet. Can't wait to see how that hits on something with more volts than an eGo.
- Status
Similar threads
- Locked
