About to pull the trigger on a Diy mixing kit

Status
Not open for further replies.
I have no clue as of what sizes .. I would like to keep things small.. I changed my mind on that kit the shipping was way out of the box. I will just piece buy will make it harder for me to start i think cause I don't know if will buy the correct stuff that was the kit..

Seriously, if you want to start small, a couple of disposable syringes, some empty bottles, nic base, PG and/or VG is all you need. Just get a couple/few flavorings to play around with, unless you just want to go unflavored. Personally, I really enjoy unflavored with 80% VG, 10% PG, and 10% water. A cheap plastic tray or shallow tub can be nice to work in, in case of spills. Disposable gloves and safety glasses are recommended if using high strength nic base. Keep a roll of paper towels handy.

You can put clear tape or nail polish on the outside of the syringes to protect the markings and use them for a long tome. Make sure you get blunt tipped needles too, one fat one and one small one. Once you start doing bigger batches, more tools become useful.
 

Heabob

Super Member
ECF Veteran
Mar 17, 2014
667
441
Bay City, Michigan
What are flasks and beakers for, lol.

I just squirt all my junk into a standard 15ml dropper top bottle, simple and cheap.

Bottles here:Empty 15ml EyeDropper Bottle Childproof Caps - Mt Baker Vapor - Electronic Cigarettes
They also have 30ml bottles.
You might need 1 or 2 empty 250ml bottles to downmix your nicotine to a lower (safer) level, for mixing, most are 100mg per ml.

Best Nic here: Nicotine - 120 mL - Vapers Tek

Good selection of flavorings: Bull City Vapor - Best Prices on DIY e-liquid Supplies
And: Electronic Cigarette, Clearomizer, USA e-Liquid, e-Cig Juice, DIY Flavors, Wholesale Nicotine, Empty Bottles for E-Liquid - ecigExpress
And: DIY E-Cig Supplies & E-Cigarette Liquid | Make Your Own E-Liquid | RTS Vapes
RTS also has NON GMO VG made from Coconuts.

USP PG can be had from Tractor Supply for about 22 bucks a gallon, but not all stores carry it.
They also have cheap syringes and needles, but the needles are sharp, and need to be cut/ground off.
 

Monotremata

Ultra Member
ECF Veteran
Verified Member
Jul 15, 2014
1,662
1,744
Fontana, CA
monotremata.bandcamp.com
Guess I gotta subscribe to this one seeing as how I was planning on getting Nude's basic starter kit next paycheck hehe..

Bouoy - check out any one of the many e-juice calculators online and the numbers and ratios will start to make sense.. The higher the nic level of your base, the less of it you use. The ratio of nicotine juice to VG and PG added determines how much its diluted.. I went and did the math a week or so ago while I was browsing all the various DIY supplies and the 'basic' kit I was going to get actually wont make that much juice in the end it turns out once I figured out how much I could make at a 24 and 18mg nic level.. You only get 50ml of 38mg base with it, so if I was to make my regular old 18mg with it, thats only going to make me around 100ml of actual juice.. That reminds me, since Im bored at work I guess I can finish my little spreadsheet I was doing comparing what comes with the kit to buying the supplies on their own hehe.. I keep waiting for Wizard Labs to come out with their kits but that things said Coming Soon for awhile now.. Better go check again..
 

rowdyplace

Super Member
ECF Veteran
Verified Member
Dec 31, 2013
921
693
80
Birmingham, Alabama
I wish wizard labs would save everything in your cart. I have had to redo it 3 times.. cause I start looking at the flavors and get tied up with stuff around here and forget I hit refresh and have to start over.. I think with me doing 3 of everything. plus a funnel a bunch of bottles I was under $50 not counting the needles..

They save things in the cart if your logged in. I know this because i just found a bunch in my cart from last weekend when I kinda stayed out too late, drank too much and started a serious order when I got home at 3am...
 
Status
Not open for further replies.

Users who are viewing this thread