aga t rebuildable atomizer issue

[Winston TheGreatest]

I Need HELP......i just got aga t rebuildable atomizer tank today and i don't get much vapor. does anybody know why there's not much vapor? my vivi nova tank produce a lot more vapor. i wrapped the coil very evenly. i did oxidized the stainless steel mash well. What do i do to get more vapor out?

 

[Deacon Aegis]

Check out Pbusardo's site, tasteyourjuice.com for a walk through on rebuilding the AGA-T's. Did you prime your wick with a few drops of fluid before trying to fire it? Several things to check, but the rebuild video there might give you some ideas of how to troubleshoot it out.

 

[Askelios]

Check that your mesh does not obstruct the hole completely

 

[crxess]

You might want to post some information about how you set the AGA up.
What materials did you use?
Wick type and build?
Wire size and # or wraps?
Final ohms reading?
device used on?

 

[ChesherCat]

I agree with crxess, more information please.

 

[Schneidermann]

If you use very fine mesh like #500 and at the same time very thick juice like pure VG that could cause a problem. Also check if your resistance ohm is too big compared to your voltage


Sent from my iPad using Tapatalk HD

 

[albcig]

you have a high resistance

 

[Dieseler]

Need more info like device used, pg.vg ratio etc.

 

[Winston TheGreatest]

You might want to post some information about how you set the AGA up.
What materials did you use?
Wick type and build?
Wire size and # or wraps?
Final ohms reading?
Device used on?

i used stainless steel mash that came with the tank and 32awg wire. i wrap 4 times and got 2.8ohms. I use with provari and setup to 5.2V.

 

[Kanj.nguyen]

Did you roll your wick solid or hollow? Should be solid.

Did you get hot spots on dry burn?

 

[AlB53]

take the fill screw out and see if that helps..and tilt it up

 

[Oktyabr]

Here is one of many AGA threads:
http://www.e-cigarette-forum.com/forum/rebuildable-atomizer-systems/405058-aga-t2.html

eHuman's blog has several *excellent* posts in it on how to get the most out of a genesis style atomizer (AGA-T+/2, etc.)
E-Cigarette Forum - eHuman - Blogs

I built mine with the included mesh and ended up using 32 gauge as well after I promptly popped that mystery gauge wire included with it. My latest wrap for it reads out at 2 ohms so I can even use it on an eGo if I like. I leave the fill screw out for better wicking and I carefully drilled the airhole out to 1.5mm from the OEM 1mm. I run 50/50 juice mostly and while it takes a second to get cooking good (I take a single primer puff, release the power button, hit it again) I get HUGE clouds of vapor from it. The only thing I like better for pure flavor is my A7 RDA.

 

[crxess]

Hope some research helps out.
Personally I think you need 28ga Kanthal at a minimum and wrap for around 1.5ohm (1.2-1.7)
Make sure all coils are heating equally. Pulse until even, on dry wick. Make sure wick has room in hole, not overly tight.

If China materials - Wire is probably NiChrome and Wick is 325 Mesh

I have 500 Mesh and it wicks 50/50 blends like a straw.

 

[cigzag]

I tip up and let the wick fill with juice then in the middle of the pull I tip down and let it sizzle then tip back up for maximum vapor. Providing your coil is setup right, voltage set correct and no hot spots this should help.

 

[Winston TheGreatest]

Woww.... i got it. thank u guys. thanks for all the answers and comments. U guys are very helpful. My tank finally works. Lots of clean vapors. I replaced new mash wick and re-wrap the coil to 2.2ohms. i drilled the air hole a little bit bigger. Lots of lots of clean vapor.

 

[SuperDave68]

i had the same problem with me aga t2. i think my problem was caused by wrapping the coil to tight around the mesh.
i scrapped the mesh wick though, because i was having problems with consistant vapes. i modded mine to use XC-116 (ceramic fiber wick) and do a U wick.
i may try the mesh wick again someday, on a backup unit though.