Ammit 25 RTA
- Thread starter Gallant
- Start date
- th_trl_thread_readers 0
- Status
For me it felts like big coil diameter blocks / reduces the airflow. So with 2.5 coils its good for me. Nice airy. Btw when the juice flow is not good and there are no or just little air bubbles comming out the juice holes I just short the wick ends a bit more. Its no problem if they touch not the bottom of the wickholes.
Great atty... but what kind of nicotine strength to be used with it? I use 12 mg/ml, there is not too much for a atty so powerful? And vape 10 ml/day...
It all depends on what you like. But generally most peeps use 3mg with these type of atties, the most 6mg. Peeps generally reserve 12mg for mtl atties.
I would say depends on what coil resistance used. I am using a 3mm 1.4ohm kanthal coil in my Ammit25 and vaping it at 16 watts.
Thanks, guys. My build: d=3mm, microcoil, r=0.65 Ω, 6 wraps, wire= Kanthal A1 (Φ 0.45 mm - 25 Gauge), vape at 22 watts. So, maybe 12 mg/ml eliquid is to mouch... my heart will explode... 
Last edited:
I use 12mg on all of my tanks including this one. I used to use 20 and 24 but finally after all these years have worked down to 12.
Nope. I was at 32mg for a long time and was stuck at 20-24 for quite a while. Just this year I’ve gone down to 12 after 8.5 years. I also use snus throughout the day.
Mixed up my last batch of juice at 1mg! Smoker for 15years, mate had a Kanger Evod, I bought that three years ago.
Would never have quit without Vaping.
Currently running my Ammit at 65w with a 0.18 SS fused Clapton. Lovely vape.
Happy Christmas all! [emoji16][emoji106]
Sent from my iPhone using Tapatalk
Would never have quit without Vaping.
Currently running my Ammit at 65w with a 0.18 SS fused Clapton. Lovely vape.
Happy Christmas all! [emoji16][emoji106]
Sent from my iPhone using Tapatalk
Leaking, leaking, leaking, leaking... Whatever I tried to do... is leaking...
I change every oring... i made 3 -4 mm coil, wick small... big... is leaking... i follow eneryting i read here, fill it then upsaidown open ac and jc... leaking.
Is a magic solution to stop the damn leaking?
I change every oring... i made 3 -4 mm coil, wick small... big... is leaking... i follow eneryting i read here, fill it then upsaidown open ac and jc... leaking.
Is a magic solution to stop the damn leaking?
where is it leaking from, the ac or the bottom. If from the bottom where the 510 pin is , sometimes the 510 is not tight and it will leak, if from your ac then its a wicking problem ie not enough cotton or to little
Thanks, ECarroll... Leaking from bottom... mainly. If i unscrew it from the mod, the top of the mod are full of juice. But i think is leaking from de ac too, because if i put a paper in there, is fill with juice. I tight 510 pin hard.
there are 2 screws on the 510, the big one you see and a little one under it. The little one is the one i meant to tighten sorry, but be carefull not to break them
where is the isolator screw? Without it know wander it leaks, The Isolator screw is the one i was talking about
I only have the isolator, like in pictures, and the big screw, the gold one, that I removed, to made the picture.
- Status
Similar threads
