Any Squonk Mod Repairer's on here ?

[Vapin_all_Hours]

Hi all, i have an RMods DNA30 squonker that's in need of repair, it's not the chip that's faulty it's the pin that goes from the juice bottle to the atty, as far as i can see there is a threaded ring that has a soldered wire attached to it and the threaded ring has somehow worked wiggly loose, it does work if you jiggle it a bit so i would think it's not making a solid connection..is there anywhere i can send it for repair ?

Thanks Chris

 

[Hans Wermhat]

Need a pic to be sure, but there is usually a nut that screws in the bottom there to hold all the parts on tight. You might be able to fix it yourself in like 30 seconds. Is the wire still securely soldered to the ring?

 

[Vapin_all_Hours]

Hi, i hope there'll be 2 pics attached...no wonder the connection is loose i've just found out the whole lot just pulls out, it has a small spring and it looks like the the brass ring should snap firm onto the white grommet at the top..so what i thought was a threaded connection turns out to be a spring...it looks like i'll have to send it someone for repair...Thanks for the reply..Chris

 

[Hans Wermhat]

It's not easy to tell, but kinda looks like that brass sleeve might just snap back on the white part. Or is the white part threaded? Can't really tell in the pic. Looks more like there is a groove in it where an o-ring might seat. Have you tried just snapping it back together?

 

[Vapin_all_Hours]

There's no threading on the white grommet it's completely smooth, the brass ring does push onto it then the springs pops it off again so i'm now thinking like you there should be an o-ring on the white grommet...i'll get me box of bits out and see if i can find an o-ring to fit, i did get this as a second user so whether the previous owner had it to bits and it dropped the o-ring without realising it...i dunno, i'll give it a go and report back later.

 

[Hans Wermhat]

There is a mod building page on this forum too. Those guys might be able to help you out with where to buy replacement parts and how to install them.

 

[vapero]

I'd the delrin (white) isn't threaded then the brass ring was just glued of press fitted
You may have to glue it
If you ruin it don't worry, looks like a fatdaddyvapes bottom feed 510 so you can certainly replace it for less than 10 bucks

Sent from my Nexus 5 using Tapatalk

 

[Dougiestyle]

I have a similar 510, and the white part is threaded. Apparently, your threads melted or stripped.. The white bushing threads into the 510 from the bottom, then the brass collar threads onto that with the spring/pin/tube in between.

Contact the builder.
Find out which 510 connector they used.
Buy new 510 connector from that manufacturer.
Remove old white bushing.
Replace with new white bushing.
Re-assemble.

 

[Vapin_all_Hours]

Hi, yes i'll look into that but at the mo i can only use the new members section.

Thanks
Chris

 

[Hans Wermhat]

Just reply in this thread a couple more times and wait till half past the hour and you will get access to the rest of the site.

 

[Vapin_all_Hours]

Hi, i've been trying to Google Rmods but there appears to be nothing about them so maybe they've stopped manufacture on the upside i can't imagine they used unique parts so i'll have nosey on fatdaddy and see if they can help.

Chris

 

[Vapin_all_Hours]

Yes i think you're right a trip to fatdaddy is in order..well i know it is because while i've been trying to fit an o-ring...i've now lost on the floor somewhere the bloody pin LOL, i am a plum at times !

 

[Hans Wermhat]

You have full membership status now. You can move about the forum freely.

 

[vapero]

FatDaddy BF Attachment Kit and BF Pins

 

[Vapin_all_Hours]

Hi, Thanks for that i'll read it thoroughly then buy the kit and give it a go.

Thanks Chris