Are you done stocking up?

UncLeJunkLe

ECF Guru
ECF Veteran
Verified Member
Nov 29, 2010
10,626
2
28,683
¯\_(ツ)_/¯
I found 9mg a comfortable place for awhile on my way to 6. Even smaller increments were useful below this. I ran into sort of wall about 5>4 where I started to get vapers' pimples, i.e zits, or bumpy red sores. Maybe a characteristic of what some believe to be the physiological dependency threshold. It happened to me so predictably that I started to work slowly through it or avoid it completely. It recurs from time to time as I occasionally configure recipes above 4.2 and varying consumption (heavy chaining) of my regular vapes likely leaves me averaging in that zone. Not everyone sees this phenomenon and I was very skeptical of any association with nic uptake until it happened to me.

Wait...so what're ya sayin'? You get zits when you decrease the nic level of your juice?
 
  • Like
Reactions: MacTechVpr

Ed Brown

Super Member
ECF Veteran
Sep 29, 2019
769
2,876
North-Central PA (flyover country)
  • Like
Reactions: Mowgli

Fidola13

Totally Stashed!
Supporting Member
ECF Veteran
Verified Member
Dec 20, 2017
10,223
57,008
Boston
I got that set too. The green is a good match for Sony VCTs and Samsung 25Rs, the brown is a good match for LG HG2s, and the gray is a good match for Molicel P26As.

I also bought that same item from Amazon. They look and feel really good.
 

UncLeJunkLe

ECF Guru
ECF Veteran
Verified Member
Nov 29, 2010
10,626
2
28,683
¯\_(ツ)_/¯
Nah they weren't that big just wouldnt shrink down enough to get rid of the fold lines.

I can't always get rid of fold lines 100%. As long as they aren't sticking up and able to be snagged, then it's good. The folds lines I haven't gotten "ironed" out can't be felt, only seen.
 

zoiDman

My -0^10 = Nothing at All*
Supporting Member
ECF Veteran
Apr 16, 2010
41,622
1
84,747
So-Cal
Nah they weren't that big just wouldnt shrink down enough to get rid of the fold lines.

It Helps (sometimes) that when you slide the Wrap on the Battery, to Smooth down the Fold with something Flat before you put the Heat to it. Like a Popsicle Stick or a Wood Ruler.

I like to Stay away from using Anything Metal. Just In Case.
 

bnrkwest

ECF Guru
ECF Veteran
Verified Member
Sep 6, 2011
10,873
36,891
Somewhere out there

rosesense

15years and counting
Supporting Member
ECF Veteran
Verified Member
Contest Winner!
  • Jan 1, 2010
    17,697
    52,266
    TN
    So how is everyone surviving? I am happily vaping as usual :) I am having a few problems with Zenith tank on Koolfire Z80, it leaks for me. But I have the .3 ohm coil so maybe that's why??
    What wattage?
     

    zoiDman

    My -0^10 = Nothing at All*
    Supporting Member
    ECF Veteran
    Apr 16, 2010
    41,622
    1
    84,747
    So-Cal
    So how is everyone surviving? I am happily vaping as usual :) I am having a few problems with Zenith tank on Koolfire Z80, it leaks for me. But I have the .3 ohm coil so maybe that's why??

    On the 1st night with my New Z80, the Zenith II/0.3 Coil Leaked. Wasn't very impressed to say the Least. But since then, I haven't had any Problems.

    I reverted back to my STM/Coil-Head days and take the Tank off the Mod at store it in a Plastic Film Container when not in use. But it Hasn't Leaked again. Allbeit I have used about 3 Coils so far.

    I'm saving that TankCoils for down the road if my Eyes become too dim or my Hands don't want to work with an RTA/RDA.
     
    Last edited:

    fiddleshe

    Vaping Master
    ECF Veteran
    Verified Member
    Dec 11, 2013
    3,432
    15,142
    Phoenix, AZ
    It Helps (sometimes) that when you slide the Wrap on the Battery, to Smooth down the Fold with something Flat before you put the Heat to it. Like a Popsicle Stick or a Wood Ruler.

    I like to Stay away from using Anything Metal. Just In Case.
    I'll use my remote then.
     

    UncLeJunkLe

    ECF Guru
    ECF Veteran
    Verified Member
    Nov 29, 2010
    10,626
    2
    28,683
    ¯\_(ツ)_/¯
    blackfriday-sale.gif
     

    Users who are viewing this thread