Attack of the (Kayfun v4) Clones!

[snow blind]

The ones that might need to vary is #16, use 11 x 1.5 mm or 12 x 1.5 mm, for the rest you can use the chart.
36 sits in the bottom end of 38 and seals the chimney with 38

Thanks man! Ok, that makes sense with 36... i dont have my v4 with me right now so i was going by memory and couldnt remember cleaning that/taking that apart yesterday. Probably sitting up in there as i had perfect vacuum and no leaks.

Hell, maybe i'll split the difference and go with the dura 70 11.5x1.5mm rings. What seems to fit best in your Tobeco?

 

[dwcraig1]

Thanks man! Ok, that makes sense with 36... i dont have my v4 with me right now so i was going by memory and couldnt remember cleaning that/taking that apart yesterday. Probably sitting up in there as i had perfect vacuum and no leaks.

Hell, maybe i'll split the difference and go with the dura 70 11.5x1.5mm rings. What seems to fit best in your Tobeco?

My Tobeco came with a 12 x 1.5 mm in spot 16

 

[MattB101]

Try here: http://www.e-cigarette-forum.com/forum/rta/625777-svo-mesto-kayfun-4-a.html#post14662661

I'm old so I type slower....

I'm using Tapatalk so it's difficult to put a link in. Thanks for the backup.

Sent with no malice and not a whole lot of forethought from my new Galaxy Tab 4. Thanks Santa!

 

[KTMRider]

I bought 12 x 1.5mm, 11 x 1.5mm, 10 x 1.5mm, 17 x 1mm 12.1 x 1.6mm.

12 x 1.5mm works best for (16). 17 x 1mm is great for almost all 22mm atomizers to seal tanks. I bought some 10 x 1.5mm for (18) but haven't really needed them. I originally bought the 12.1 x 1.6 for (16) but it's way too big and I had to sand it down to fit.

 

[NavyChief52]

Really enjoying the performance and readability of the HCigar iteration. What's the group recommendation for a black instance? It appears as if HCigar isn't making one.

The HCigar just works, no leaking, still on the original o-rings, the juice control works well. I have no regrets.

 

[snow blind]

I bought 12 x 1.5mm, 11 x 1.5mm, 10 x 1.5mm, 17 x 1mm 12.1 x 1.6mm.

12 x 1.5mm works best for (16). 17 x 1mm is great for almost all 22mm atomizers to seal tanks. I bought some 10 x 1.5mm for (18) but haven't really needed them. I originally bought the 12.1 x 1.6 for (16) but it's way too big and I had to sand it down to fit.

What material did you go for the buna 70/90/silicone etc?

 

[KTMRider]

What material did you go for the buna 70/90/silicone etc?

Buna 70 for all.

 

[snow blind]

Buna 70 for all.

Ok cool, that's what i figured but wanted to make sure. I'll order some from o-rings and more... with the way i lose parts down the sink those bags of 50 will last me a few months lol.

 

[KTMRider]

Really enjoying the performance and readability of the HCigar iteration. What's the group recommendation for a black instance? It appears as if HCigar isn't making one.

The HCigar just works, no leaking, still on the original o-rings, the juice control works well. I have no regrets.

I have the Tobeco black version and it was leaking slightly from (16). I just replaced it with a 12 x 1.5mm o-ring. My silver Tobeco is still perfect.

 

[twolostminds]

Has anyone had the chance to compare the Tobeco and HCigar clones side by side?

 

[Apulo]

Really enjoying the performance and readability of the HCigar iteration. What's the group recommendation for a black instance? It appears as if HCigar isn't making one.

The HCigar just works, no leaking, still on the original o-rings, the juice control works well. I have no regrets.

Both of my Tobeco clones, black and stainless, have been flawless after a thorough cleaning. So much so that I bought a Tobeco in Blue.

 

[KurrptSenate]

any suggestions about trying temp control for the first time on this kayfun v4?

 

[TheKiwi]

any suggestions about trying temp control for the first time on this kayfun v4?

1) make sure leads are very very securely held by the screws.

2)take base reading when juice control is fully opened

3) vape on it with JC fully opened.

That's all I got. I run my k4s with ni200 and it's been working well


Burping out loud using Tapatalk

 

[Marc411]

any suggestions about trying temp control for the first time on this kayfun v4?

I've been capturing the leads under both screws using Ni200 and Titanium and it's been performing well in the EHPro, Tobeco and Fasttech models.

 

[KurrptSenate]

one coil, but both screws?

thanks

 

[sos2001]

After a couple of weeks, I have 3 versions.....

Infinite-flawless, no issues

EHPro-with the replaced "flat" tip base again no issues

Tobeco-juice control still will not turn unless the 510 pin is loose, but vapes well.

Think I'll stop for a while with three.

 

[Monotremata]

Both of my Tobeco clones, black and stainless, have been flawless after a thorough cleaning. So much so that I bought a Tobeco in Blue.

Where did you get the blue one? Maybe I'll get a third one now.

 

[ricks]

After a couple of weeks, I have 3 versions.....

Infinite-flawless, no issues

EHPro-with the replaced "flat" tip base again no issues

Tobeco-juice control still will not turn unless the 510 pin is loose, but vapes well.

Think I'll stop for a while with three.

Is your 510 pin hitting your air screw?

 

[mudram99]

Is your 510 pin hitting your air screw?

Hey Rick, have you by any chance received those spare part kits we ordered for the V4s? I haven't yet.

 

[Apulo]

Where did you get the blue one? Maybe I'll get a third one now.

http://kanvape.theshoppad.com/#/pro...a-rebuildable-atomizer-tobeco-clone-pre-order

Sent from my SGH-M919 using Tapatalk