AVAILABLE NOW - SMOKtech TT Terminator Tank Rebuildable Dripping Atomizer and/or Tank Fed Atomizer System; Available For a Very SPECIAL Price! VIDEO W

[DaxFX]

Mine should be delivered tomorrow acording to tracking.


Sent from my iVap using Tapatalk HD

 

[hobbes4]

Received mine yesterday. Haven't used it yet but looks promising. Can you tell me what the clear rubber piece is for? It looks like those white rubber caps you use on cartos if you don't have a drip tip.

Also, will you offer polypropylene tank tubes or can you direct me to one that will work?

Thanks.

 

[VapingTurtle]

...
Also, will you offer polypropylene tank tubes or can you direct me to one that will work?

Polypro Tubes

 

[djtonyb]

Got one and stuck it in my AGR... not bad, but even wide open it doesn't seem to feed fast enough to keep up with my vaping. It reads 2.2 ohms, and I usually vape 2.2 ohms at 3.8v, but if I go much over 3.5 it tastes like it's on the edge of burning. Nice fit in the AGR, though. Not a bit wobbly.

 

[rdsok]

Got one and stuck it in my AGR... not bad, but even wide open it doesn't seem to feed fast enough to keep up with my vaping. It reads 2.2 ohms, and I usually vape 2.2 ohms at 3.8v, but if I go much over 3.5 it tastes like it's on the edge of burning. Nice fit in the AGR, though. Not a bit wobbly.

Sounds if you are on the edge of a dry burn ( not getting enough e-liquid in )... open the gap just a little bit more so more e-liquid can get in quicker

 

[hobbes4]

Thank you VapingTurtle for the polypro link.

Does any know what the clear rubber piece is for? It looks like the white caps that come on cartos but since it comes with a drip tip i'm assuming it goes somewhere else.

 

[VapingTurtle]

Thank you VapingTurtle for the polypro link.

Does any know what the clear rubber piece is for? It looks like the white caps that come on cartos but since it comes with a drip tip i'm assuming it goes somewhere else.

Ya collect 4 of them and glue them to the bottom of the legs of your chair. They let the chair slide quietly on the floor while you vape the TT.

 

[MwSlim]

Received mine yesterday. Haven't used it yet but looks promising. Can you tell me what the clear rubber piece is for? It looks like those white rubber caps you use on cartos if you don't have a drip tip.

Is that what those are for?? Lol I always wondered what they were



Sent from my iPhone using Tapatalk 2

 

[keelalagirl55]

Ya collect 4 of them and glue them to the bottom of the legs of your chair. They let the chair slide quietly on the floor while you vape the TT.

Smarty Shell

 

[hobbes4]

Ya collect 4 of them and glue them to the bottom of the legs of your chair. They let the chair slide quietly on the floor while you vape the TT.

I vape in a rocking chair, hahaha. I'm assuming i don't need it then so i'll just keep it with all my other random vape stuff/parts.

 

[VapingTurtle]

I vape in a rocking chair, hahaha. I'm assuming i don't need it then so i'll just keep it with all my other random vape stuff/parts.

I've got a couple stashed, but never found use for them. When ST first started including them with DCTs they said that they were an optional spacer. But I never figured out what needed spacing.

Too small for cat toys.

 

[djtonyb]

Sounds if you are on the edge of a dry burn ( not getting enough e-liquid in )... open the gap just a little bit more so more e-liquid can get in quicker

Got it! I didn't realize I was opening the top threads that are where the coil hits the outside... LOL! Now that I have that part tightened down properly I can easily adjust the threads that are for the feed holes... I had to watch a couple of videos on the Killer to figure out what I had missed. It really does work great in the AGR tank! I was disappointed when I realized the Ravens didn't fit, but now I want to order a few more Terminators (I didn't even bother with the tank it came with, I knew the locking feature of the AGR would make it so much easier to use).

 

[DaxFX]

Recived mine today,, i didnt liked. Feels very cheap, when unscrew for get the juice hole opened its woble a lot, everything slide a lot, the plastic tank have a dent, if you want to use it as a tank stay away from this, if you want a dripper with a tank look dripshield then may be worth. If this thing was a bit better design on how to open and close juice feader hole would be better, but for me is a thumb down. I will use it as a dripper wile the coil last then is into the trash

http://www.youtube.com/watch?v=NWqnBJJK9zA


Sent from my iVap using Tapatalk HD

 

[Teach]

Recived mine today,, i didnt liked. Feels very cheap, when unscrew for get the juice hole opened its woble a lot, everything slide a lot, the plastic tank have a dent, if you want to use it as a tank stay away from this, if you want a dripper with a tank look dripshield then may be worth. If this thing was a bit better design on how to open and close juice feader hole would be better, but for me is a thumb down. I will use it as a dripper wile the coil last then is into the trash

Smoktech TT terminator tank - YouTube


Sent from my iVap using Tapatalk HD

I see from your video that the atty base is unscrewing from the 510 adapter that runs down through the tank base. Try tighten up the atty base (bowl part) to the 510 adapter before you insert it into the tank.

I also found that once the base is securely tightened you can open the upper atty by holding the base of the tank. See if that helps.

Took me some fiddlin' to get used to it, but after that it worked great.

 

[DaxFX]

Ok, thanks looks like i did start with the wrong side, so i needto unscrew on the bubble to get the juice feed and not in the 510 to 510 adapter? The wobble stay no matter in what place i get unscrewed the atty..

http://www.youtube.com/watch?v=lL1woBltCm8,

A bit better now but still cheappy feel and wobling


Sent from my iVap using Tapatalk HD

 

[DaxFX]

Ok, thanks looks like i did start with the wrong side, so i needto unscrew on the bubble to get the juice feed and not in the 510 to 510 adapter? The wobble stay no matter in what place i get unscrewed the atty..

http://www.youtube.com/watch?v=lL1woBltCm8,

A bit better now but still cheappy feel and wobling


Sent from my iVap using Tapatalk HD

Ok. Now as a tank is working better, as a dripper i do liked, but i wasafraid using as a tank after my first try, fidling a bit here and there and im getting an exellent vape, good flavor now, i still dont like the cheap wobling feel but vapes really nice..so 3 stars out of 5


Sent from my iVap using Tapatalk HD

 

[djtonyb]

I've been using this exclusively today, in the AGR, and this little thing rocks! I want to grab a couple more when budget allows. I'd really like to see them sold without the tank, though. I'd much rather a cheaper price on these and then buy a couple more AGRs to plunk them in. I seriously am liking this better than my Protanks.

 

[djtonyb]

Ok, thanks looks like i did start with the wrong side, so i needto unscrew on the bubble to get the juice feed and not in the 510 to 510 adapter? The wobble stay no matter in what place i get unscrewed the atty..

Smok terminator tt tank - YouTube,

A bit better now but still cheappy feel and wobling


Sent from my iVap using Tapatalk HD

The 510-510 is where it unscrews for the juice feed... the threads in the bubble are to change the coil/wick/ceramic cup. The threads in the bubble should be snugged down tightly... I can see where this would make a regular carto tank wobbly, but it really works well in the AGR. Even with the long tank, there's enough of the cylinder poking out that it's easy to adjust the feed to wherever you want it. It must be a royal pain if that 510-510 isn't locked down somehow.

 

[DaxFX]

Now im confused,, so i misunderstood "TEACH" but he told me the the 510 adapter needs to be very tight and open and close the other threading, and that do make sense to me also because in the bubble threading also have a hole...

I use the TT all day today with the 510 very tifgt to adapter and opening/closing the booble threading and did works perfect,,

So like "chapulin" "y ahora quien podra defenderme"


Sent from my iVap using Tapatalk HD

 

[Adrena]

Gave up in the wobble the screwing and thus unscrewing silly system..
Happy to say my RAVEN flanged fit nicely in the tank
Now I have a huge raven tank and a kicking dripper not all is lost >;<

Raven in the Terminator Tank...