Battery for my setup help

[espkh123]

Hey guys!
I ordered my new hcigar Nemesis mod Clone from VapeRoyalty with a new Patriot rda.

I plan on running at lowest .4ohms (rarely) but sticking to .5-.8 ohms.

What battery should I get?

Im looking for something that is safe, low cost, and reliable at those ohm settings.

Thanks!

 

[espkh123]

Ugh I'm dumb...
I want the big 18650 size.

 

[savagemann]

Can't go wrong with an AW 1600 mah imr battery.

 

[VapoJoe86]

MNKE IMR 18650 will do you right. 30 amp continuous draw limit will keep you well within safe limits on pretty much any build. For example, a 0.2 ohm build will draw 21 amps on a full battery and still be safe, bit I would never make a 0.2 ohm build to begin with!

 

[espkh123]

MNKE IMR 18650 will do you right. 30 amp continuous draw limit will keep you well within safe limits on pretty much any build. For example, a 0.2 ohm build will draw 21 amps on a full battery and still be safe, bit I would never make a 0.2 ohm build to begin with!

What do you recommend to charge it?
Care to post a link?
I dont want to blow money on the wrong stuff! *again*

 

[KenD]

Sony US18650VTC4 (and VTC3) are good as well. 30 amps, 2100 mAh (for the VTC4, the VTC3 is 1600 mAh I believe)

Sent from my GT-I9100 using Tapatalk

 

[VapoJoe86]

What do you recommend to charge it?
Care to post a link?
I dont want to blow money on the wrong stuff! *again*

I charge mine with a nitecore intellicharger i2. I got the charger and a 2 pack of the batteries at vaporbank.com, a nearby B&M that I trust. The charger and the batteries work great!

 

[DasBluCig]

Hey guys!
I ordered my new HCigar Nemesis Mod Clone from VapeRoyalty with a new Patriot RDA.

I plan on running at lowest .4ohms (rarely) but sticking to .5-.8 ohms.

What battery should I get?

Im looking for something that is safe, low cost, and reliable at those ohm settings.

Thanks!

If your mod will accept a FLAT-TOP battery.....the Sony VTC4 30A is a good bet.....and the Intellicharger i2 is what I use with my AW IMR 18650 1600's (button-top)....this particular AW is rated at 24A - pushing a bit below .5 ohm, but I run around 1.0-1.2 so the 24A limit (for ME) is actually a little overkill.....but BETTER SAFE----THAN SORRY!!
Happy (vaping) Trails!

 

[bender817]

When you look at the nitecore charger and you see the i4 you will want it, but unless you only charge 1-2 at a time, it will take forever. The mA output to each battery gets reduced when charging in parallel. Basically means less batteries will give you a faster charge. My friend put 3 MNKE's, and the Panasonic 18650B 3400mah on his i4 all at once and it took close to 14 hours to get the 3 MNKE's done. He took them off and the darn 3400mah took another 6 hours. I don't have that kind of patience so would never run more than 2 on a charger at once.

Sent from my SAMSUNG-SGH-I747 using Tapatalk

 

[Exile]

Sony 18650 VTC4
Sony US18650VTC4

AW 18650 1600mah
AW IMR 18650 3.7v 1600mAh - Batteries

Nitecore Intellicharger i4
http://rtdvapor.com/index.php/battery-chargers/nitecore-intellicharger-i4.html