Hello peeps~
I just build my very first coil ever. Woot! I got a Kayfun a month or so ago and went down to my local B&M and had my guy show me how to make one for that. I have been using that same coil and changing out the wick every so often until today. Today I got an M8 from the classies and I HAD to try a build. I cannot find a video anywhere to help me with any part of it and there were no instructions. I have been learning about ohms and watts and whatnot, got me an Ohm reader (not sure why because I have 2 MVP 2.0s and an Evic Supreme and was not planning to go sub ohm) but I watched a video of a 3-post dual-coil build and figured I had nothing to lose!
I used 28 gauge wire for 8 wraps each and ended up at .8. Since my Evic Supreme will not let me screw up with the voltage/wattage I stuck in my cotton and set it up. Seemed to work pretty good but I was not getting very large clouds. This tank fills by pressing the tip down which drops juice onto the deck. Pretty snazzy, but I have NO idea how many drops it takes.
Turns out not very many I think. I was messing around with the wattage to try and find one that gave me the experience I was expecting from a .8 build but I ended up leaking juice out of the air holes. Argh. Also, after a short time my build started reading .7 and it has stayed there since.
Sorry, there really is a question here, I swear! What I need to know is what is number for a .7 build? I was staying at the lowest setting the Evic would allow (12.4) and it was not enough I don't think. I just turned it up to 20.4 watts and that seems better but I got a lot of leakage after my first pull on it. Is that normal? Probably flooded it? I don't want to go too high and ruin the build. i am kind of attached to it at the moment, it being my first one and all.
Thanks for letting me ramble. Any tips you can give me will be much appreciated!!
I just build my very first coil ever. Woot! I got a Kayfun a month or so ago and went down to my local B&M and had my guy show me how to make one for that. I have been using that same coil and changing out the wick every so often until today. Today I got an M8 from the classies and I HAD to try a build. I cannot find a video anywhere to help me with any part of it and there were no instructions. I have been learning about ohms and watts and whatnot, got me an Ohm reader (not sure why because I have 2 MVP 2.0s and an Evic Supreme and was not planning to go sub ohm) but I watched a video of a 3-post dual-coil build and figured I had nothing to lose!
I used 28 gauge wire for 8 wraps each and ended up at .8. Since my Evic Supreme will not let me screw up with the voltage/wattage I stuck in my cotton and set it up. Seemed to work pretty good but I was not getting very large clouds. This tank fills by pressing the tip down which drops juice onto the deck. Pretty snazzy, but I have NO idea how many drops it takes.
Turns out not very many I think. I was messing around with the wattage to try and find one that gave me the experience I was expecting from a .8 build but I ended up leaking juice out of the air holes. Argh. Also, after a short time my build started reading .7 and it has stayed there since.
Sorry, there really is a question here, I swear! What I need to know is what is number for a .7 build? I was staying at the lowest setting the Evic would allow (12.4) and it was not enough I don't think. I just turned it up to 20.4 watts and that seems better but I got a lot of leakage after my first pull on it. Is that normal? Probably flooded it? I don't want to go too high and ruin the build. i am kind of attached to it at the moment, it being my first one and all.
Thanks for letting me ramble. Any tips you can give me will be much appreciated!!
