Bulli A2-T
- Thread starter BigBulli
- Start date
- th_trl_thread_readers 0
- Status
The threads aren't stripped or stripping it's just an extremely tight fit to get it seated properly. I do think your, "Hey dummy did you remember to vaseline the threads," statement may just be the key to getting my bottom plastic in easy peasy.
Oh and I realized another use for the A2 the other day. You can start fires using the coil. Goodbye Bic's and Zippos!
Oh and I realized another use for the A2 the other day. You can start fires using the coil. Goodbye Bic's and Zippos!
Last edited:
As of the 30/9 sale. Anyone got theirs yet? Emailed cetin, no replies.
They've been holding onto their "no emails requesting tracking, its a waste of our time" policy. I think it may still say that somewhere on the site. I ordered mine on the 6th of september and received it only yesterday or the day before so I'd just sit tight and be patient. This way you'll be surprised when it shows up and not constantly disappointed it didn't come yet
Man, plastic on metal sounds like something that's reallyyy easy to crossthread. In my experience with work, vaping, tinkering and stuffs - I find that if you lightly pull away from where its screwing in when you first get it threaded in (first two threads), if its a little loose to start its usually a good thing. If its pretty tight to start, its usually a sign its crossthreaded. Idk if its the same as far as the iatty goes, just saying in terms of my experience with certain electrical stuff and light fixtures.
Just got word that the 30/9 shipment is out today. Good news people!!
I didn't get a notice
. The waiting game is my worst enemy!
Just got word that the 30/9 shipment is out today. Good news people!!
That's good news I ordered on 9/5 and then again on 9/30 I hope both of mine ship out soon.
No notice here.
I didn't lube the bottom connector, I never had a problem with it fitting though. I probably crossthreaded thing though. @RCXD thanks for the shipping notification!
Hi all!
Today I have received the Mega Tanks atomisers from Bulli, and I'm very satisfied, though I have some problems maybe you could help me out a bit.
1. It leaks a bit between the bottom part and the middle part, just where the threads meet. Is there something I can do to stop the leaking. This is not pocket friendly this way!
2. The draw when inhaling is too light because of the 1mm hole. How can I make the draw a bit harder? Like a more permanent solution than the tape someone mentioned. Anyway tape won't work if it makes contact with the juice..
I made a lower resistance coil..around 1.9 Ohm and I'm happier than with the stock resistance, but so far no wicking or other issues. The workmanship is of a very high quality and I am really impressed.
If only you could help me a bit on the issues I mentioned above, I would be much happier with these atomisers.
P.S. Where can I get hold of good fibre glass wick and Kanthal in the EU?
EDIT: I was delighted to find that the eGo cones fit the Rivas too. I need to start thinking of a good battery set up because 750mah batteries aren't cutting it enough for me. Is the Bulli Smoker Elite Link: Bulli-Smoker Elite - Bulli-Smoker GmbH any good? I don't want a bulky PV.
Today I have received the Mega Tanks atomisers from Bulli, and I'm very satisfied, though I have some problems maybe you could help me out a bit.
1. It leaks a bit between the bottom part and the middle part, just where the threads meet. Is there something I can do to stop the leaking. This is not pocket friendly this way!
2. The draw when inhaling is too light because of the 1mm hole. How can I make the draw a bit harder? Like a more permanent solution than the tape someone mentioned. Anyway tape won't work if it makes contact with the juice..
I made a lower resistance coil..around 1.9 Ohm and I'm happier than with the stock resistance, but so far no wicking or other issues. The workmanship is of a very high quality and I am really impressed.
If only you could help me a bit on the issues I mentioned above, I would be much happier with these atomisers.
P.S. Where can I get hold of good fibre glass wick and Kanthal in the EU?
EDIT: I was delighted to find that the eGo cones fit the Rivas too. I need to start thinking of a good battery set up because 750mah batteries aren't cutting it enough for me. Is the Bulli Smoker Elite Link: Bulli-Smoker Elite - Bulli-Smoker GmbH any good? I don't want a bulky PV.
Last edited:
thanks eye!
which one should I buy? I prefer a resistance of 1.7 - 2.3 Ohms, with 4 to 5 coil turns.
using Riva batteries currently, so that would be an initial of 4.2v down to 3.7v
which one should I buy? I prefer a resistance of 1.7 - 2.3 Ohms, with 4 to 5 coil turns.
using Riva batteries currently, so that would be an initial of 4.2v down to 3.7v
The A2-TM is on my list of must-haves. The option of a smaller hole is definitely welcome. One can always drill it out but filling-in a hole is much harder...
Thanks,
Lee
Thanks,
Lee
FYI: I got a Bulli T last night in SS both holes were drilled by Bulli.
I got the Big tank not the Standard Ego set up I wonted but that's ok. I passed it on in a tried already due to having another coming from the 9/30 sale. I will be picking up at least one more Bulli A2 with the T tank just to have around.
I hope Ace reports back here as to how he likes it.
Here is a few photos of the set up I got
I got the Big tank not the Standard Ego set up I wonted but that's ok. I passed it on in a tried already due to having another coming from the 9/30 sale. I will be picking up at least one more Bulli A2 with the T tank just to have around.
I hope Ace reports back here as to how he likes it.
Here is a few photos of the set up I got
Last edited:
OMG they moved the date up another 10 days. Are you f'in kidding me???
---
I am here: http://maps.google.com/maps?ll=32.588426,-83.664093
---
I am here: http://maps.google.com/maps?ll=32.588426,-83.664093
- Status
Similar threads
- Locked
- Locked
