Can I fix this? Tobh Clone
- Thread starter CCCCakezilla
- Start date
- th_trl_thread_readers 0
- Status
I think you can loosen the center pin from the bottom and adjust that. Lemme know.
Yes, stick a small allen Key through the hole to grip.
Loosen the 510 screw a bit and turn the pin back into place.
Hold it secure and tighten the 510 center pin.
Loosen the 510 screw a bit and turn the pin back into place.
Hold it secure and tighten the 510 center pin.
Mine does that all the time I just grab the center pole with needle nose to straighten and hold while tightening center pin with flathead.
you want to try get the coil or coils as close to the airhole/s as possible without touching which will keep the 2x32g to stay cooler as it fires up fast and allow you to take a longer pull, the flavour will be much better than just having the coil/s in the well, the only downside to this is that you will have to have long long legs to reach the side of the atty but if you set up your coil/s as i have in the pic it will save you some wasted leg length.
i just thought i'd mention it cus i see a lot of people say they're getting an awful vape from the tobh, i know its not what you are asking but if it helps, all good
i just thought i'd mention it cus i see a lot of people say they're getting an awful vape from the tobh, i know its not what you are asking but if it helps, all good
I've had great performance with my Tobh set up like the pictures above. Question though, I thought I had read somewhere that the 510 pin length can by shortened a bit, however now that I've had the unit for a bit I cannot figure it out. Am I chasing a unicorn, or am I missing something?
you can sand or file down the copper pin on the bottom of the 510
D'oh!!! BRILLIANT!
if you put the sandpaper or file on a flat side and rub the pin on it you will be able to grind it away while keeping the flat surface on the pin
Last edited:
you want to try get the coil or coils as close to the airhole/s as possible without touching which will keep the 2x32g to stay cooler as it fires up fast and allow you to take a longer pull, the flavour will be much better than just having the coil/s in the well, the only downside to this is that you will have to have long long legs to reach the side of the atty but if you set up your coil/s as i have in the pic it will save you some wasted leg length.
i just thought i'd mention it cus i see a lot of people say they're getting an awful vape from the tobh, i know its not what you are asking but if it helps, all good
I built like this today and got incredible results!
I'm more than satisfied with my Tobh now.
Thanks so much brother!
Sent from my SGH-S959G using Tapatalk 2
Better than I did. Builds like that on the stock Tobh definitely get better results though.
Since this thread, I traded my Tobh for another VTC4 and bought a Plume Veil though. :\
The particular clone that I got felt very cheaply reproduced. I don't have any experience with an authentic Tobh, but the barrel on mine felt thin. Almost as if it were aluminum.
Also, the airholes were very small and, because of the slots on the deck (airflow), it was a little difficult to build on.
I had experience with the Plume Veil and I'm really familiar and enjoy all of it's features.
I'm sure I'll cross paths with another Tobh, but I'll definitely inspect it before I purchase it again.
Also, the airholes were very small and, because of the slots on the deck (airflow), it was a little difficult to build on.
I had experience with the Plume Veil and I'm really familiar and enjoy all of it's features.
I'm sure I'll cross paths with another Tobh, but I'll definitely inspect it before I purchase it again.
- Status
Similar threads
- Locked
- Locked
