T
Catfish atty mods.
- Thread starter Chowderhead1972
- Start date
- th_trl_thread_readers 0
- Status
If you have the deck bottomed out with no connection your 510 is blown out (stretched too deep). Is your 510 screw ground down or smooth?
not a problem. Just go to my album and pick out any one you want. After all it is Christmas and the least I can do.....oh wait...that was yesterday....oh well there's always next year.
Hehehe... So I just checked out your album. I can see you not giving up a single of those beauties. What a sweet collection!
the pin is smooth,it just blows me away the magma works,rm3 works,cyclone works.so your thinkin I need to put a S/O kit in because the connection has been shoved down?...right?btw the deck never bottoms out it just stops cuz it gets so hard to turn.was scarey tightening down the atty when it was hardly wanting to turn.in the end it never bottomed out
Last edited:
The pin is pressed into a rubber grommet so you can go inside and push or wiggle it upward a little bit. Assuming you have checked continuity everywhere else.
Do you mean pull it out a little? I have tried it on 4 working Reos and it won't fire on any of them but it fires on the VW mod I tried it on to pulse the coils. Could the center pin be pushed in too far do you think?
I just got a PM from pdib. Apparently the screw IS adjustable so I will give it a shot in the morning after I get over my pissedoffedness at it!
Last edited:
the pin commin out the bottom of the atty is ok,it sticks out about a 16th of an inch give or take.took the delrin out of the reo and the nipple the tube and bottle slide onto wasn't very tight and juice was all over.so at least be able to fix the leak but don't know about connectivity issues.Rick
Just a note here Rick, Rob mentioned a short while back that some of the newer grands had kinda shoddy 510's in them. I had the same problem putting a CH Odin on one of my grands not threading down flush and not firing. I very carefully re-tapped the 510 in it and the atty them screwed all the way down and fired finally. I would suggest sending it in to Rob or Tom to have it done, because it is very easy to crush the wafer thin washer in the 510...
Is it just the Odins then that have a problem? His other atty's are firing fine.
That was the only one I had a problem with. Authentic and clone alike. I have heard of some people having problems with Mephisto's, but that one has a pin that can be adjusted. I have to adjust mine on occasion.
I knew I shoulda stepped away,now I get to wait for a S/O kit from rob.this hasn't been my day.trucks broke then atty not working then frustration gets to and and WHAMO over tighten the stooopid pin on the reo.i quit.thanks for all the great advice and suggestions.just isn't my 24hrs.start over next week when the s/o kit gets here.there showed that reo!just throw it in a drawer!gone drippin!
I can't wait for the new Anti-Hoople 510! I bet PDIB is thinking the same thing right now.... The issue more often than not is the Reos 510. The REO unlike almost ant other device it has a fragile 510 that just can't stand up to the abuse of changing attys frequently.
Anyone know where I can get an engraved button cover? I think my setup needs a little more writing on it.
I swear I would trade one/all of my children for Rob to come out with a flat top Reo Grand that is just a millimeter wider to fit 22mm RDAs flush.
Also, if anyone is frustrated with different vertical builds in the Veritas try a single horizontal coil pretty much blocking the air hole. It's what worked for me and kept me from selling it. Not that it wasn't an awesome BF conversion by CH, but I was really having a hard time getting a decent vape out of it for my style of vaping. The single coil almost blocking the air hole completely changed it to a winner for me. Flavor equal to my magma and quite a surprising bit of vapor production as a bonus.
just thought I'd share this with y'all... my favourite atty: the frankendoge. chowderhead BF doge deck, negative grub screws from hobo v2 to eliminate the "negscrews touching topcap" problem some doges (including the authentic apparently) have, positive screw and copper barrel from FT 1:1 copper doge clone, pmma chuff also from FT. I also have the 1:1 non BF deck for it, so I can use this rig on my reo or a standard mod.
thanks tom!
thanks tom!
Hey Tami, could you put me on the Marquis list?
After checking out that atty webwise, it sounds amazing - like an improved Veritas. Is Tom's version gonna come with the tools too?
After checking out that atty webwise, it sounds amazing - like an improved Veritas. Is Tom's version gonna come with the tools too?
- Status
