Thank you brother! I'm spending eight hours a day at the shop to fill orders now so it will be sooner rather than later ill keep ya posted!
How big is the hole in the pin of that marquis ?
Catfish atty mods.
- Thread starter Chowderhead1972
- Start date
- th_trl_thread_readers 0
- Status
How big is the hole in the pin of that marquis ?
Marquis should be a #53, it a m3 bolt with the head turned down to m2 diameter.
8hrs? That it? I was close to 20 a day leading up to the Derringer. I do have short days though.
I could have drilled much bigger on the Marquis but the screw is under a lot of strain when building the coils to to the incredibly tall center post, I wanted to leave at least 80% of the strength of the solid bolt. #53 seemed like a fair compromise.
8hrs? That it? I was close to 20 a day leading up to the Derringer. I do have short days though.
I could have drilled much bigger on the Marquis but the screw is under a lot of strain when building the coils to to the incredibly tall center post, I wanted to leave at least 80% of the strength of the solid bolt. #53 seemed like a fair compromise.
Last edited:
It doesn't seem to drain very well?
It's only on the "Squo" part of Squonked. Once the "ked" part happens it drains fine.
Also don't do that tongue cheek thing again, you're creeping me out.......
Last edited:
Paid for Vertex, plus 2 ss Derringer dt's & 2 black Derringer dt's.
PM also sent.
PM also sent.
I just got my Veritas today...unbelievably fast, I didn't expect it for another couple of days. I'm already on my 2nd build...the first one didn't heat up fast enough. I'm playing with a single coil horizontal build...8 wraps of 28 ga. for 1.1 ohms. It works ok for now. I'll keep playing till I get it right 
.
View attachment 407576
CH...Thank you, I'll definitely be back for more!!
Todd
.View attachment 407576
CH...Thank you, I'll definitely be back for more!!
Todd
I'm pushing .24. The Marquis likes power. My first set of coils on the Marquis were .43, very limp and airy. I'm using 2 Marquis one with a .29 on a REO and the afforementioned .24 on my TMod.
I just got my Veritas today...unbelievably fast, I didn't expect it for another couple of days. I'm already on my 2nd build...the first one didn't heat up fast enough. I'm playing with a single coil horizontal build...8 wraps of 28 ga. for 1.1 ohms. It works ok for now. I'll keep playing till I get it right
View attachment 407576
View attachment 407577
CH...Thank you, I'll definitely be back for more!!
Todd
Dual coil 6wrap 26ga @2.3mm and .33 ohms was my goto atty For months on the Veritas. The density is the best I have had to date, the Marquis is right there with it but likes a bit more power. See my previous post.
I gotta say that sniper gray Cerakote is a great color. It doesn't look very good on their chart but in real life it's great , I think it's My favorite with the cut squonk holes.
Love that marquis on top too.
Love that marquis on top too.
I'll give my build a day and see how I like it. I'll definitely give this one a try...it's a little lower ohms than I've gone before, but I have to try it sometime...thanks for the info.
Todd
I'm a firm believer that the impedance required for a great Vape has much more to do with the atty than the vaper. There are exceptions to that of coarse but it makes a good starting point.
Payment statuses updated on the spreadsheet if i missed any let me know ....
Bold with strike thru numbers at the quantity of items will show paid status
[emoji116]
Bold with strike thru numbers at the quantity of items will show paid status
[emoji116]
Last edited:
Thanks for the work Turk. My first time looking at the spreadsheet in a while. Looks great
The future is bleak...
The future is bleak...
Eaten back, MommaBird, Distortoblotto, Calpis, Pauly3, your attys will be ready today. Check the spreadsheet in Turks sig.
https://docs.google.com/spreadsheets/d/tBUia59bGb1G0EAGfxzI3bw/htmlview?pli=1
https://docs.google.com/spreadsheets/d/tBUia59bGb1G0EAGfxzI3bw/htmlview?pli=1
Last edited:
CH, Lancia ended up bouncing around the postal system for a couple of days. If I actually get it today, I'll send it first thing in the AM. Sounds like you have enough to keep you busy.
All of the delivery companies are haywire right now.. I have a shipment of mills and bits that I ordered last Friday from Massachusets 2nd day air (ups) that hasn't made it out of the state yet, I have tools that were supposed to be delivered by USPS Monday that might just make it here today, the have been in Capitol heights md since Monday. Dhl Is the shining star they are only running a few hours late. I would do better selling attys door to door I believe.
- Status
