Chit Chat in VOLTVILLE Thread #2 :)

Status
Not open for further replies.

grego66

Super Member
ECF Veteran
Jun 10, 2012
369
452
58
Nevada
Hi All Volties,

I wondered can anybody recommend a good SI cartomizer?

My Nano stock is almost at an end, I bought in bulk when they were discontinued. I have been looking at the T3 Bottom Coil Clearomizer can anybody give any feedback on performance with a X2 (is that battery powerful enough) and is there any leaking issues?

The two main things I am looking for is something that I can get a good hit with using a X2 and no leaking. The Nano's were decent for both points I thought. I was bit upset they discontinued them.

Thanks
 
  • Like
Reactions: Wuzznt Me

cindycated

ECF Guru
ECF Veteran
Verified Member
Jul 19, 2011
10,304
30,936
San Francisco, CA
Hi All Volties,

I wondered can anybody recommend a good SI cartomizer?

My Nano stock is almost at an end, I bought in bulk when they were discontinued. I have been looking at the T3 Bottom Coil Clearomizer can anybody give any feedback on performance with a X2 (is that battery powerful enough) and is there any leaking issues?

The two main things I am looking for is something that I can get a good hit with using a X2 and no leaking. The Nano's were decent for both points I thought. I was bit upset they discontinued them.

Thanks
Sorry, grego - didn't want your question to go unnoticed. Somebody more knowledgable will come along and give their opinion, but mine is that I didn't care for the T3 (the regular one, not the Aspire one). I hated the draw, there wasn't enough flavor, the resistance was too high for X2s, the head was a pain to rebuild or maintain,...I dunno. I just didn't like them. I never got a chance to try the BDCs or iClear 16 (had already switched to Vision VT and Evods with adapters by then), but I hear those are good (but I think they recommended Spinners with the BDCs, so not sure about those). I'm hoping they've found a permanent fix to their supply problems with replacement heads - there was a problem with that for awhile. If you liked the Nano, you might try the Mini (under "X2 Clearomizers") or the CE3s on closeout.
 
Last edited:

awsum140

Resting In Peace
ECF Veteran
Verified Member
Jun 12, 2012
9,855
46,386
Sitting down, facing forward.
Hi All Volties,

I wondered can anybody recommend a good SI cartomizer?

My Nano stock is almost at an end, I bought in bulk when they were discontinued. I have been looking at the T3 Bottom Coil Clearomizer can anybody give any feedback on performance with a X2 (is that battery powerful enough) and is there any leaking issues?

The two main things I am looking for is something that I can get a good hit with using a X2 and no leaking. The Nano's were decent for both points I thought. I was bit upset they discontinued them.

Thanks

It all depends on your particular style of vaping. I used T3s for a while on X2s and then the Spinner, better performance on the Spinner by the way. I did, and still can, rebuild them easily and used rayon wick in them when I did. I also ended up drilling out the center pin and air holes to improve air flow, but that's my style of vaping coming through. Unfortunately, the Nano can't be rebuilt and the CE3 has also been discontinued.
 

grego66

Super Member
ECF Veteran
Jun 10, 2012
369
452
58
Nevada
Thanks cindycated and awsum140 for the info especially concern the T3.

I think I will try the Mini next, my only concern with them was the short wicks but that shouldn't be too much of a problem. As for the T3 I only have X2 bats at the moment and I think going by what you both say that isn't powerful enough to give me the hit I like.

What are the Mini's like for leaking? That was my other concern. I loved the Nano's but occasionally more often than not after about a weeks worth of use they would start to leak. I had to keep wiping drops of juice off of the top of the battery.
 

3mg Meniere

Vaping Master
ECF Veteran
Verified Member
Mar 24, 2013
6,493
65,098
75
Tomah Wisconsin
I used the nanos a lot for sampling new juices. I just Googled, and there are other vendors offering them for real good prices. Probably trying to unload excessive stock. I remember when SI was in the process of getting rid of them, they were good prices also.
 

tmcase

ECF Guru
ECF Veteran
Verified Member
Apr 20, 2011
20,862
54,652
Ah, that's it. I never owned a vamo and up until recently, my mechs have all had 18500 batteries. I would use a long PV if it came with one of these to push the button for me:
97bdefd233e1a1b5aac1d882c77e9204.jpg

:laugh:

If I had one of those, I wouldn't be thinking about vaping. :evil::lol::blush::facepalm:
 

3mg Meniere

Vaping Master
ECF Veteran
Verified Member
Mar 24, 2013
6,493
65,098
75
Tomah Wisconsin
All you ladies talk a good game, anyway :lol:
I try. But given my past experiences, it is just talk. Too many hurts.
AH - The "Button" excuse - It is always about the "BUTTON" . . . :facepalm:

However, I DO . . . :lol: :lol: :lol:
I had totally forgotten about THAT button. :pervy:
 

grego66

Super Member
ECF Veteran
Jun 10, 2012
369
452
58
Nevada
I used the nanos a lot for sampling new juices. I just Googled, and there are other vendors offering them for real good prices. Probably trying to unload excessive stock. I remember when SI was in the process of getting rid of them, they were good prices also.

Thanks for the info, but now I am kind of looking forward to trying the Mini. It looks like the Nano model is being stopped everywhere so I will have to move off them soon. When the juices are restocked I'm going to get a couple of Mini's to try.
 

cindycated

ECF Guru
ECF Veteran
Verified Member
Jul 19, 2011
10,304
30,936
San Francisco, CA
Thanks for the info, but now I am kind of looking forward to trying the Mini. It looks like the Nano model is being stopped everywhere so I will have to move off them soon. When the juices are restocked I'm going to get a couple of Mini's to try.
I never got a chance to try them, but I kinda remember the Mini being their answer to all the complaints that the Nano got when it first came out. ;)
 
Status
Not open for further replies.

Users who are viewing this thread