- Status
Was going to get one, but showing sold out when I got home from work. Page says the next batch will be available at 11pm PST . . . that's 2am for me 
I've been waiting patiently for them to come back in stock and now they're releasing them in batches at times when I can't be online . . . suffice it to say I'm more than a little peeved
I've been waiting patiently for them to come back in stock and now they're releasing them in batches at times when I can't be online . . . suffice it to say I'm more than a little peeved
Yep, will need to pick up one of these. Considering my new found love of lr 306s
They are rotating the times so everyone can get a shot from all time zones. They really are trying to do this to the best of their ability and for those who want to make a purchase.
Yes, you are right. I was not in the best of moods already yesterday and hadn't read the blog post, all I saw was the time listed on the product page. For the most part, my post was just me blowing off steam and I intended no disrespect or insult to anyone.
I'm following them on twitter, now, and I'll be keeping an eye out throughout the evening ;-)
I'm following them on twitter, now, and I'll be keeping an eye out throughout the evening ;-)
Good luck and I do hope you are able to get a hold of one!!!!!!!! We all have days like that and need to vent.
Ack! They came on the site last night and I just found out . . . I checked twitter and the site in the afternoon and didn't look again after that. Oh well, I don't technically need one, anyway I've got other toys I've got my eye on, so I can save this purchase for a later date
I've got other toys I've got my eye on, so I can save this purchase for a later date
The dca is the best thing dripping wise i have experienced...the ma306 atty is also very nice and holds A LOT of liquid compared to any other attys i have tried...picked up another yesterday from the twitter special that has 3 different caps to fit all sorts of 306's....anyone have any good recommendations on 306 attys other than the MA306?
I have been using the Cisco attys and love them.
I would love to get some different caps I have some 3.0 306's I use at 6v that I love but there just a bit to small to use in the DCA. I have been looking at ways I can mod the DCA so they would work.
Is there any one using there DCA with a Darwin. Should be a good combo. I am picking up a Darwin when there available.
Last edited:
Yep, I've been using mine on my Darwin. The arm can even close fully with it on, which is something I couldn't quite manage with a drip shield ;-) I've been using 3 and 4 ohm attys from MadVapes, they're slightly larger OD than the ma306, but I find the air flow is a lot more comfortable with them even though the top piece was fitted for the ma. With the included ma306, the draw is very tight and I find myself pulling so hard just to get a good hit that I'm sucking juice right up out of the atty and into my mouth . . . I mean, I like a tight draw and all, but with that atty in the DCA it's like trying to suck a golf ball through a drinking straw
Last edited:
Thaks KJ. I hope to get a Darwin when Drew has them on the site. I love my DCA's I use the Cisco 306's in it and love it. I have been using my DCA's on my ProVeri for the time been but look forward to the Darwin and DCA combo.
To make the cisco306 fit into the standard top I just use a thin (1mm) strip of the nice stock paper that came with the DCA. I place the thin strip on the inside side wall of the top and then slide the atty in. The extra paper left I just tear off. Kind of a lame hack but it works.
A modder here makes some pieces of DCA in ss after people demand here and asking for that.
Not for mass production due to respect of good sense guys there.
It has two upper ends to fit empires and cisco atomizers 306.
All from ss food grade.
Not for mass production due to respect of good sense guys there.
It has two upper ends to fit empires and cisco atomizers 306.
All from ss food grade.
- Status
Similar threads
