Hi All, I saw a video review on the 4nine copper clone and the top cap has no contact, the 510 on the atomizer is supposed to touch directly on to the battery but some say the 510 connection on the Tobh Atty V2 clone is too short. Anyone tried this before? Let me know. If it won't fit any other atomizer clones you might recommend?
Does the Tobh Atty V2 clone work on the 4nine copper clone?
- Thread starter dledo1
- Start date
- th_trl_thread_readers 0
- Status
Not sure about the Tobh. If it has a screw pin for the 510 you could put an oring under it. Also some of the 4nines come with a top cap that has an adjustable screw pin that makes the connection between the 510 and the battery top. The magma works. Are you looking for drippers or tanks also?
-Dirk
-DirkWhat are you using on your Neme? I hope you have patients and some experience. The 4nine is not a pull out of the box and vape away mod in my experience. It takes some trail and error to get it to work right. As far as recomending an atty.....what kind of experience are you looking for and what is your skill level. There are so many factors that come into play and personal preferences. Keep asking questions and learning.
- Dirk
- Dirk
Not sure about the Tobh. If it has a screw pin for the 510 you could put an oring under it. Also some of the 4nines come with a top cap that has an adjustable screw pin that makes the connection between the 510 and the battery top. The magma works. Are you looking for drippers or tanks also?
Perhaps I'm wrong but I haven't seen a 4nine that comes with anything other than the hybrid 510 connector. I don't have one, but I'm in the market for one and haven't seen it yet. So unless there happens to be one then the OP would be correct. Assuming that there isn't a large difference in the length of the 510 among the different clones of the tobh.
I've got a tobh clone that works fine on my 4nine clone!
Not sure what version it is. The basic rule with RDAs and a hybrid topcap is to make sure the positive pin in the 510 of the RDA goes past the negative part of the connector (threaded part that surrounds the positive pin). You want the pin to make contact with the battery, not the negative part... If the negative part touches the battery you get a hard short and the battery will get really hot and likely vent.. Which may also fry the polarity on the magnets used in the button.
It's a nice mod! Super short and tiny even in 18650 mode. The button takes some work to get it smooth though. If you hit it just right it's not a problem. Otherwise you need to file down the edges of the button lightly, and the area inside the body where the switch sits and slides. i haven't done that yet... Working good enough for me without it.
Sent from my iPad using Tapatalk HD
Not sure what version it is. The basic rule with RDAs and a hybrid topcap is to make sure the positive pin in the 510 of the RDA goes past the negative part of the connector (threaded part that surrounds the positive pin). You want the pin to make contact with the battery, not the negative part... If the negative part touches the battery you get a hard short and the battery will get really hot and likely vent.. Which may also fry the polarity on the magnets used in the button.
It's a nice mod! Super short and tiny even in 18650 mode. The button takes some work to get it smooth though. If you hit it just right it's not a problem. Otherwise you need to file down the edges of the button lightly, and the area inside the body where the switch sits and slides. i haven't done that yet... Working good enough for me without it.
Sent from my iPad using Tapatalk HD
Have a look at Focal ecig "improved top cap" for the 4nine. My brass 4nine came with that type of cap. I don't use the adapter pin, but it is available. The authentic doesn't use it.
-Dirk
It sure does dledo! I own the authentic, infinite and Tobeco clone of the Tobh Atty V2, and it works amazingly with the 4nine! I even own the 26650 version of the 4nine, and the 26650 Tobh Atty by Tobeco, and they seem to be made for eachother.
To be honest, the 4nine will work with ANY atty with a 510 connection that pokes out past the threads (which is basically everything). And ALL of the Tobhs have fairly long 510 connections, so the answer to your question is yes, they will work no matter which tobh you get. The 4nine is partly awesome because it SELF ADJUSTS via magnetic repulsion, meaning it literally holds the battery up and against you atty's 510 constantly, and when you fire it's just your finger overpowering the switch up into the negative battery side. Quite ingenius and simple, I get an amazing .04 voltage drop from .2ohm atty!!!
By the way, nice taste!
The 26650 version of this is my favorite setup thus far, it can't be beat!
Last edited:
I have this set up w/ a 18650 right now. Makes contact fine.
Bangin' w/ a "T style" dual coil set up.
Bangin' w/ a "T style" dual coil set up.
- Status
Similar threads
- Locked
- Locked
