Dripper atty question
- Thread starter Ctalbot
- Start date
- th_trl_thread_readers 0
- Status
It looks like you can use the Igo W and the Igo l with it. You just have to build above whatever the resistance cut off is for the MVP 2. http://www.e-cigarette-forum.com/fo.../485656-what-best-device-dripping-mvp-v2.html
Honestly due to the low amp limit in the mvp IMHO dripping isn't going to give you the best experience. If you want more than your normal fill and go tanks I would suggest getting a kayfun or similar to build your own coils and also get some benefits of building your own. If you really want to drip and arent looking for more throat hit or stronger flavor then as long as you stay above 1.1ohm i believe it is youll be ok not sure how much wattage youll get at that though.
Have you considered looking for a new mod? Perhaps a dna 30 or similar or even a mech mod if youd be comfortable with that?
Also the dripper isn't as important as the coil you build, you can pick up a igo-w or similar and be fine or you can get fancy and buy one with adjustable airflow and such, I will say with some of the cheaper ones you may need to drill out an airhole to get the correct airflow for your taste and vapor needs.
Have you considered looking for a new mod? Perhaps a dna 30 or similar or even a mech mod if youd be comfortable with that?
Also the dripper isn't as important as the coil you build, you can pick up a igo-w or similar and be fine or you can get fancy and buy one with adjustable airflow and such, I will say with some of the cheaper ones you may need to drill out an airhole to get the correct airflow for your taste and vapor needs.
any dripper will work with it....BUT your coils will be the limitation. Dont expect to become a cloud chaser or anything with an MVP is just doesnt have the muscle. You are just too limited by amps and by ohms that the mvp will fire.
IMO you wont be able to get all the benefits from dripping using that mod. Since your looking to get into dripping I would suggest looking into regulated devices like DNA 30s or even 100watt/150watt devices (Its nice to have options 
). I would stay far away from the Cloupor T5 as I have had many issues including mine almost starting a fire while I was asleep. 
Aside from regulated mods check out mechanical mods. The market is currently saturated with mods but dont let that intimidate you: they all will perform about the same. Personally I like copper for its beauty and awesome conductivity! I have an overdose clone and a stingray v2 clone. Both I have no complaints about.
IF you decide to go with either of the above recommendations you will want to get GOOD batteries, GOOD charger, and ohm reader.
Batteries: sony vtc5, sony vtc4, or other high drain battery. Vtc5s are virtually impossible to find and cost an arm and a leg if they are real. (The fake ones are not that bad IMO!!!!! (as long as they are not the re-wrapped Panasonics)
Charger:I recommend xtar because.... well they're awesome. But intellicharger will work just fine.
I have gone into way to much detail. If ya need anymore help just drop me a line! Hope this helps
(Plume veil RDA is awesome btw)
). I would stay far away from the Cloupor T5 as I have had many issues including mine almost starting a fire while I was asleep. Aside from regulated mods check out mechanical mods. The market is currently saturated with mods but dont let that intimidate you: they all will perform about the same. Personally I like copper for its beauty and awesome conductivity! I have an overdose clone and a stingray v2 clone. Both I have no complaints about.
IF you decide to go with either of the above recommendations you will want to get GOOD batteries, GOOD charger, and ohm reader.
Batteries: sony vtc5, sony vtc4, or other high drain battery. Vtc5s are virtually impossible to find and cost an arm and a leg if they are real. (The fake ones are not that bad IMO!!!!! (as long as they are not the re-wrapped Panasonics)
Charger:I recommend xtar because.... well they're awesome. But intellicharger will work just fine.
I have gone into way to much detail. If ya need anymore help just drop me a line! Hope this helps
(Plume veil RDA is awesome btw)
I'd say it would depend on your reason for wanting to drip. I have an MVP2, and wanted to drip to be able to sample different juices easily, and to have the control necessary to create my own coils without the cramped space of the smaller tanks/heads. I also wanted something that I could continue using when I do get some larger mods. While I don't anticipate to get mech-mod-level taste or cloud performance, I expect it'll still be a big improvement over the clearomizers I was using.
Based on reviews here and elsewhere, I picked up an Magma clone last night. I chose that model because (a) it can run either the single-coil setup more befitting the lower-powered MVP or a dual-coil, in both cases with the coils being centered below the drip hole, (b) the tank size wasn't huge, and (c) its airflow control is very versatile, especially if you're using as a single vs dual coil.
Based on reviews here and elsewhere, I picked up an Magma clone last night. I chose that model because (a) it can run either the single-coil setup more befitting the lower-powered MVP or a dual-coil, in both cases with the coils being centered below the drip hole, (b) the tank size wasn't huge, and (c) its airflow control is very versatile, especially if you're using as a single vs dual coil.
You can absolutely drip with an MVP. Though I wouldn't necessarily recommend a rebuildable dripper... Check out these links and get your toes wet in the dripping pool first... then, if you like it, you can move on and up in gear...
The Ocelot's Guide to Dripping:
Drip, Drip, Drip - The Sound of Dripping
Here are some Disposable 510 Drippers like Occy was referring to:
510 Standard Resistance Dripping Atomizer
Bridgeless 510 Atomizer, 2 ohms
The Ocelot's Guide to Dripping:
Drip, Drip, Drip - The Sound of Dripping
Here are some Disposable 510 Drippers like Occy was referring to:
510 Standard Resistance Dripping Atomizer
Bridgeless 510 Atomizer, 2 ohms
The MVP is a great mod to use while learning to rebuild (if you are interest in a rebuildable dripper).
Yes, you will be limited (mine won't fire below .8ohm) but you can still run a RDA or RTA on it. I use my KFL+ v2 (an RTA) at anywhere between 1.2-1.8ohms all the time!
Or, as Kaezziel pointed out, there are non-rebuildable drippers you can get as well!
Yes, you will be limited (mine won't fire below .8ohm) but you can still run a RDA or RTA on it. I use my KFL+ v2 (an RTA) at anywhere between 1.2-1.8ohms all the time!
Or, as Kaezziel pointed out, there are non-rebuildable drippers you can get as well!
Last edited:
If you want to put a dripper on the MVP, I'd personally use a 28mm (26650 mod sized) atty. Why? Lots of deck space to build on and learn, lots of room for error, and it's big and easier to unscrew at the end of the day than some slippery, hard-to-grasp 22mm or 21mm width atty. A friend of mine was running a zenith on his Sigelei 30W (I know it's not an mvp, but it's a box mod), and when I dropped an Asmodus RDA on that thing, he never went back to the zenith.
But to each his own, and I'm very much a convention-breaker. I don't like rules very much. Being a former bike messenger will kinda do that to people.
But to each his own, and I'm very much a convention-breaker. I don't like rules very much. Being a former bike messenger will kinda do that to people.
as i know that actually any attys are similar, the key for good vaping is building a coil, wicking, airhole
why vendors make many design is reason for art. some atty looks nice on some batery.
as a nob, sorry if my words are wrong
why vendors make many design is reason for art. some atty looks nice on some batery.
as a nob, sorry if my words are wrong
You're pretty much correct, mbahcis...
Some attys are a little different, the Tobh has a cone shape inside the top cap that helps with the airflow... others do different things to "improve" airflow or airflow regulation... deeper juice wells... the way the posts line up... the size of the post holes... but for the most part, all of the dripping attys are just metal build decks with a top cap to seal everything up... I like that there are so many out there though. It lets you pick what works for you... performance and aesthetics...
Some attys are a little different, the Tobh has a cone shape inside the top cap that helps with the airflow... others do different things to "improve" airflow or airflow regulation... deeper juice wells... the way the posts line up... the size of the post holes... but for the most part, all of the dripping attys are just metal build decks with a top cap to seal everything up... I like that there are so many out there though. It lets you pick what works for you... performance and aesthetics...
I picked up a mutation x mostly cause it's cheap and lots of holes, I want a dropper for a few reasons, to taste better, change tastes often, to show smokers how different things taste and to have a ground level for building coils and such.. This Is all for learning and I'm gunna do the best I can with what I have for now..
- Status
Similar threads
