Bad... Are you putting the ptb all the way around the coil or just at the slots?
E2 Cartomizer Technical Discussion
- Thread starter zoiDman
- Start date
- th_trl_thread_readers 0
- Status
Bad... Are you putting the ptb all the way around the coil or just at the slots?
not all the way around, just covering slots but you can go wider as i do as well sometimes. works great either way but the tail seems to be best, so ptb with tail like in my video.
*chirp* *chirp*
Quiet in here tonight. Everyone passed out from nic overdose?
Quiet in here tonight. Everyone passed out from nic overdose?
I'm enjoying my E2 right now instead of analyzing it. Am working on neglected genealogy stuff while waiting for bad to let us know about the new ones.
I got my Big Brother VV today so I've been playing with it. It works just like the Little Sister except it carries two 14500's. Sweet mod.
I'm vaping an e2 on my Little Sister right now. Didn't know the Big Brother was available yet. Guess I'd better check my bank balance and see if a Big Brother is in the near future for me
dont wait for my review
ill let you guys test them, the 510 are at 2.4 to 2.6, they dont seem to leak without the inner cap but they still have some primer that needs to be burnt off, they made a booboo on the samples so they are sending those out , these seem to be improved but there isnt a new cup, they cut slits to the inner plug to match the slits on the cup, it helps but using the low ohms on a 3.7 still isnt wise.
I dry burnt them, cleaned them in hot water, dry burned again, then it was fine, seems to wick a tad better Which i take it is form the cleaner wick(still has primer residue but less).
I did the ptb method to them and they work better obviously.
the 808 are 2.9 to 3.0 and a couple at 2.8, those are much better at 3.7 and above. , also need a dry burn or a wash. no leaking so far and work well but ALOT better with ptb.
the 3.0 ohm ones pretty much work like they should with no mods but need to be dry burned or washed. other then that they have been vaping properly.
even after they fix the cup if they keep the same wick i guess its fine but it needs to be tested further, but nothing they do will come close to cutting the wick and using ptb. but i dont think thats what their intentions where since it produces tons of vapor on its own and maybe im just being a selfish ..... wanting the most amount of vapor known for a carto.. lool
ill let you guys test them, the 510 are at 2.4 to 2.6, they dont seem to leak without the inner cap but they still have some primer that needs to be burnt off, they made a booboo on the samples so they are sending those out , these seem to be improved but there isnt a new cup, they cut slits to the inner plug to match the slits on the cup, it helps but using the low ohms on a 3.7 still isnt wise.
I dry burnt them, cleaned them in hot water, dry burned again, then it was fine, seems to wick a tad better Which i take it is form the cleaner wick(still has primer residue but less).
I did the ptb method to them and they work better obviously.
the 808 are 2.9 to 3.0 and a couple at 2.8, those are much better at 3.7 and above. , also need a dry burn or a wash. no leaking so far and work well but ALOT better with ptb.
the 3.0 ohm ones pretty much work like they should with no mods but need to be dry burned or washed. other then that they have been vaping properly.
even after they fix the cup if they keep the same wick i guess its fine but it needs to be tested further, but nothing they do will come close to cutting the wick and using ptb. but i dont think thats what their intentions where since it produces tons of vapor on its own and maybe im just being a selfish ..... wanting the most amount of vapor known for a carto.. lool
Last edited:
The Buzz voltage has now been lowered for the E2 vapors. I thought about getting one, but decided that I didn't need a large mod.
Plenty low enough for me. On the first mark it's reading 3.4v, but if I dial down below that I can get readings as low as 2.8v.
At least one issue is corrected..
Is the inner cap still the same minus that? Still a little finicky to get seated back on the cup?
Think about the BB, br. It's just a simple-looking 2AA box mod from the outside. I honestly don't know how he gets everything in that box. They're not on his site yet but I believe they'll be $74.99. Box Mods. The Janty stick pouch fits perfectly for belt carry.
I'm vaping an e2 on my Little Sister right now. Didn't know the Big Brother was available yet. Guess I'd better check my bank balance and see if a Big Brother is in the near future for me
If you have the LS the vaping experience is the same. I just like to collect mods.
yes it is and even worse now becuase you need to match the notches, this wont be in r4 thank god. but i filled it to the rim without the inner plug and had no leaking, so...
but like i said nothing beats the ptb, the ce2 brother mod rocks the most but you need 1 long tube for each side and not everyone has tons of cartos with those long tubes laying around so im not even making videos on it.
i tested many so far of the r3 v1 and these and so far to get the full beast out of the e2, the ptb with a tail kicks me in the ... the most and banjos mod makes it work like it should so both are good for me.
but like i said nothing beats the ptb, the ce2 brother mod rocks the most but you need 1 long tube for each side and not everyone has tons of cartos with those long tubes laying around so im not even making videos on it.
i tested many so far of the r3 v1 and these and so far to get the full beast out of the e2, the ptb with a tail kicks me in the ... the most and banjos mod makes it work like it should so both are good for me.
Last edited:
Snap... yeah, thankfully it wont be in r4... good to hear it's not leaking though.
I was cleaning on of my XL's tonight and made the mistake of running a stream of hot water into the carto to rinse. One of my PTB plugs got knocked loose and went bye-bye inside the carto. From now on I'll be soaking them instead.
Hi guys,
Just to save me a little time... what are the general (short list) of issues I might run into on the pre ceramic versions??
One of you guys is sending one or two to me for a trial.
Just to save me a little time... what are the general (short list) of issues I might run into on the pre ceramic versions??
One of you guys is sending one or two to me for a trial.
If you have the LS the vaping experience is the same. I just like to collect mods.
Like a lot of folks, I'd like to have the extended battery life of the BB. I really like the LS, but I'm a pretty heavy vaper, so the extra battery time would be a welcome benefit for me.
It really depends on what revision you end up w/. The issues can range from pinched wicks to glue smell/taste, etc. I liked the r2 plastic cups, except that my slots eventually warped and caused it to leak.
Believe me, I've already thought about it as well as others. If I use KR8's on 3 volts though, I can use what I already have. I've just been hoping for 510's at 3Ω, but it doesn't look like that will happen.
- Status
Similar threads
- Locked
- Locked
