Eleaf GS Air Fan : Part 2

Status
Not open for further replies.

Skullman

~ Membered ~
ECF Veteran
Verified Member
Jan 30, 2013
651
6,421
South Sound Lahar Zone

Hey Ocala: Veteran, I'm not so sure about that!?? Alright This is MY 13 Cents Worth! I Don't Ultrasonic! I Feel if I Have to Go That Far it's Time to Build or Rebuild Anyway!

You Asked; How many times before you start Completely Fresh? I say Anytime Taste, Flavor & Vape are Not Up to Your Standards or Has Been Compromised! START FRESH!!!

If it's Light Colored eliquid I Hot Water Rinse or Soak for a number of minutes then I capture the Rinsed or Soaked Coils with a Partial Plastic Triangle to hold them all together (use what ever you have to keep them together) while I let a Hair Dryer on Med High Heat and Lo Speed Run on them until Dry. Which Depends on Size and Density of Coil! They will Dry Out from Direct Heat, Air and the Natural Steaming Off from Heat. This allows me to be able to have access to them in a Short Amount of Time! No waiting over night or longer to dry out! You will also know right away after applying a small amount of liquid if it is still vaping to Your High Standards or if Not it's Time to Rewick or Rebuild! I've been doing this For a Long Time Now with Excellent Results! Has saved me much time from rebuilding every time! With a Real High Quality & Costly Coil or a High Quality Build or Rebuild I Feel I should get a Good Life From Them! I mean Really! Why not get the life out of it if you can! Now with Air Coils or the Older Kangers I'm a bit different with them as cost is nominal and now rebuilding is of ease! Tend to rebuild more often!

Braided, Twisted, Clapton Style or other Exotic Builds or High Quality Coils like for the Atlantis, Kanger Mini Subtank, Ecotank, VT Coils and the Like Deserve to get The Life Out of Them Till Quality of Vape Drops then it's time................! Never Compromise Vape & Flavor!

Amount of time before rebuilding is based on so many factors it's hard to judge but I've had Quality Coils Last a Month or Longer Before I just Rebuild because so much time has gone by! I'm not so worried about Rewicking as much as I used too because of Temp Control! Unless I Screw Up Settings and Burn the Cotton then I Rewick but my use of cotton is really down these days because of Rayon! Thanks Cheechako! But I'm Real Curious to How the New SMOK High End Coils will do in the same situations!?? We will See!

Darker or Dark eliquid is a Whole Other Beast! As Well as Some Very Strong Flavors! Like your Cinnamon's, Peppermints, Absinthe & The Like! To be Judged Individually! This Also Goes for My Own Built or Rebuilt Coils! Or for that matter Your Own Built or Rebuilt Coils!

I May be Judged for My Ways But it Works For Me!

~ I Really Like the GS-MS Tanks they are a Great Size! Fits Many of My Mods So Well! And Hell, They Look Good and Vape Even Better!

Veritable Flavapalooza ~ I Like That! I Really Do!

You Should Have That Kind of Vape & Flavor At All Times! No Compromises! EVER!

Strive For That With All Your Coils, Builds and Rebuilds! You Will Be A Happy Camper!

Veritable Flavapalooza!

Again, This is MY 13 Cents Worth! Ocala, Your Mileage is Going to Vary That's For Sure!!!

Good Luck! Vape On!

Skully {:{}


PS: Sorry I've Gone on and on again.....

Question for the veteran coil rebuilders.

Clean and Rewick OR Rewind and Rewick?

Putting the coils through a soak clean, dry burn and Then the ultrasonic and drying before RW sounds like more a PIA than it's worth.

I know I can disassemble and rewind as fast as all that.

But that disassembly Does add some wear and tear to the plug and other components...

What say yall and if you Do Ubersonically clean and rewick, how many times before you start Completely Fresh?

PS; Got 3 GS MS filled with Ohm's Vapes, Blue Moo, Root Beer Float and Strawberry Shortcake, a veritable Flavapalooza!

Bruce in Ocala, Fl
 

Skullman

~ Membered ~
ECF Veteran
Verified Member
Jan 30, 2013
651
6,421
South Sound Lahar Zone

Good Mornin IMRs and All! Yep, Looks the same way here! Over cast a bit cloudy but it was warm for here in the low 60's today or yesterday now. But they are saying No More. Temps dropping then the Rain and Wind is Coming!

This is it for here too! I'm already gettin a bit depressed.............?

All The Best Everyone!

Skully {:{}


Well, so much for the run of nice weather. I think this is it, after yesterday. :rolleyes:cb
 

Skullman

~ Membered ~
ECF Veteran
Verified Member
Jan 30, 2013
651
6,421
South Sound Lahar Zone

80's WOW!

How's that Little One LV? You Still in High Heaven? Wait, that was a Stupid Question wasn't it!

I Know You Are!

We are counting down the days over here!

Skully {:{}


We are supposed to have a high of 80 today! It's NOVEMBER! :facepalm:
 

Skullman

~ Membered ~
ECF Veteran
Verified Member
Jan 30, 2013
651
6,421
South Sound Lahar Zone

~ I Really Know How You Feel Nanny! I'm Going with Aliens Too! Michigan, Where's That? Ha Ha..... Hey, I want to be there, in the Green Chair! {:{}


Yep, ALIENS!
We broke records here for three days this week - it was gorgeous and sunny and mid 70's which is totally unheard of at this time of the year. We enjoyed it so much and got all the outside work done for the season. It seriously felt like summer again all week.
Then the bottom fell out last night, the wind kicked up and it just poured rain for hours. So many leaves fell in the wind and rain, it looks like we never even tried to clean up. It's cloudy and about 50 degrees now and I AM DEPRESSED. Why is Michigan even on the MAP?
images
 

tiburonfirst

They call me 'Tibs"
ECF Veteran
Verified Member
Feb 23, 2010
26,883
260,345
The TC tank would work as well. I like that tank but not for TC! Lol

nobody is forcing you to use it with tc coils ;) the proportions are definitely better than with the m tanks!

So gotvapes has the MS tanks in stock but I don't think I'm going there! :facepalm:

lynn, let me repeat again - all shops use cc processors and getting scammed comes down to that not the individual vendor ;)
 
Status
Not open for further replies.

Users who are viewing this thread